DeDietrich DHD7000X - 2 Installing the Hood

2/ INSTALLING THE HOOD
EN
1)ForthecorrectoperationoftheDowndraft,itisimportantforittobeinstalledcorrectly.
Before proceeding with installation
2)Beforeinstallingyourappliance,removeallsafetyprotectionsasillustratedinFig.2-2b
–2c–2d.
3)Themotorisdeliveredxedtotheappliancetopreventanydamageduringtransport.Itis
necessarytoremovethemotorpriortobeginningtheinstallation.
4)Makearectangularopeninginthebackpartofthekitchentopwiththefollowingdimensions:
790x1000(seeFig.3).
5)Ifyouwishtopositionthehoodsothatitisattachedtothecooktop,itispossibletojointhe
hoodopeningtothecooktop.
6)Beforemakingtheopening,checktheinsideofthecabinetlevelwiththehoodareatomake
surethereisnoframeworkorotherelementsthatcouldadverselyaectthecorrectinstallation.
Makesurethatthesizeofthehoodwithitsmotorandtheworktoparecompatiblewiththeunit
soastoallowinstallation.
7)Applytheadhesivetothebottompartofthecornice(Fig.11)andplaceitinsidetheopening
inthekitchentop.ThenttheDowndraftinsidetheunit.
Installation
8)Fitthehoodinsidetheunit,introducingitfromabove.
9)Thesteelcorniceofthehoodmustadhereperfectlytotheupperkitchentop.
10)Fastenthehoodinsidetheunit,usingthespecialbrackets(Fig.5A).Accordingtothesize
oftheunitandtheoverallsizeoftheairexhausttube,usethefasteningbracketsprovided.
Motor
11)Themotorhasbeendesignedtobexedtothehood.Proceedtotthemotor,adjusting
theairexhaustoutlettotherequiredposition,facingupordown(Fig.6).
12)Themotorcanbefastenedeithertothefrontortobackpartoftheappliance.Toinstallat
theback,proceedasfollows:unscrewtheplateinthebackpartofthehood,screwinthemotor
inplaceoftheplate,connectthemotorwiringcorrectlyandscrewtheplateintothefrontpart
ofthehood.
Whenthemotorhasbeeninstalled,proceedtottheairexhausttube.
Warning:donotmakeanyotherholesintheappliance,asthiscoulddamagetheinternalsli-
dingpartsaswellastheelectricalparts.
13)Positionthemetalboxwiththeelectricalpartsinanareathatcanbeaccessedeasilyfor
assistanceinterventions(Fig.6)andconnecttheelectricconnectorstothehood.Warning:be
suretofollowtheguidelinesandwarningsinthesectionabout“Howtoconnectthehood”
14)Connecttheappliancetothemainselectricity.
Downdraft calibration
Afterthedowndrafthasbeeninstalled,theaspirationpanelmustbecalibrated.Thisoperation
isnecessarytoregulatethepowerexstractionoftheaspirationpanel.Connecttheproductto
thepowerline,makingsurethatit is conformed to the supply voltage indicated on the tech-
nical data tag. Pushing the ON/1 button (g. 8)theaspirationpanelrises.Afterithasreached
aheightof180mmfromthecooketop,pressOFF,tostoptheextractionthentheTimer(g.8)
andafter2sec.theOFFbutton.
Thedowndraftwillcarryoutthecalibrationofitsaspirationpanelrisingandretractingforsome
centimeters.Duringthisphase,thebuttonsonthepushbuttoncontrolpanelblink.Attheend
ofthecalibration,theaspirationpanelgetbacktothepreviouspositionandthebuttonendto
blink.Waituntiltheaspirationpanelstopsmovingbeforere-activatingtheextraction.
Warning: calibrationneedstobecarriedoutcorrectlysincethisoperationwillplayanimportant
partinyoursafetybothduringinstallationandwithregardtogeneralsafetyrules.
31