What to do if the water level is too low in my DeDietrich WHE 2.24?
If the water level and/or pressure are too low in your DeDietrich Boiler, first, ensure water is circulating properly by checking the water pressure in the heating circuit, and that flow and return valves, as well as valves and radiators, are open. Then, top up the heating circuit with water and visually inspect for any water leaks.
How to fix air pressure error due to insufficient draught in DeDietrich WHE 2.24 Boiler?
To address an air pressure error due to insufficient draught in your DeDietrich Boiler, inspect the fresh air inlet and flue gas discharge ducts (or the forced flue). Then, press the Reset button for 2 seconds. If the problem continues, further assistance is needed.
What causes flue gas temperature sensor error in DeDietrich WHE 2.24?
A flue gas temperature sensor error in your DeDietrich Boiler may be caused by insufficient draught. Check for adequate draw on the chimney connection. The boiler is in safety shutdown until the flue gas temperature sensor is again operational, so wait 15 minutes. If the problem persists, further assistance is needed.
What to do if the temperature sensor circuit is broken in DeDietrich Boiler?
If the temperature sensor circuit in your DeDietrich Boiler has been broken or short-circuited, first ensure that the water is circulating properly. Check the water pressure in the heating circuit and verify that the flow and return valves, as well as the valves and radiators, are open. If the problem persists, further assistance is needed.
What to do if no flame is detected after 5 attempts in DeDietrich Boiler?
If your DeDietrich Boiler fails to detect a flame after 5 attempts, press the Reset button for 2 seconds. If the issue continues, further assistance is needed.
How to fix communication error between safety control box and PCB in DeDietrich Boiler?
To fix a communication error between the safety control box and the PCB in your DeDietrich Boiler, check the cable connecting the safety control box and the PCB. Then, press the Reset button for 2 seconds. If the problem persists, further assistance is needed.
Why is there no current to my DeDietrich WHE 2.24 Boiler?
If there's no current to your DeDietrich Boiler, check the electrical connections.
General| Category | Boiler |
|---|---|
| Maximum Working Pressure | 3 bar |
| Fuel Type | Natural gas |
| Nominal Heat Output (kW) | 24 kW |
| Efficiency | Up to 109% |
| Gas Connection | 3/4" |
| Type | Condensing |
| DHW Production | Instantaneous |
Explains warning symbols for safety and specific information relevant to user comfort and operation.
Details manufacturer, installer, and user liabilities and responsibilities for proper boiler operation and maintenance.
Critical safety warnings related to fire, gas, burns, and equipment damage during operation and installation.
Provides essential recommendations for safe operation, installation, and maintenance practices for the boiler.
Overview of the boiler's features, including modulation range, efficiency, and key components for both models.
Explains the layout and function of the boiler's control panel, including indicator lights and buttons.
Defines the meaning of indicator lights for various operational states like standby, heating, and errors.
Guides users on how to adjust key settings like heating temperature and domestic hot water temperature.
Instructions for setting the summer/winter mode and the desired heating circuit temperature.
Instructions for setting the desired domestic hot water (DHW) temperature using the thermostat.
Details the procedures for safely stopping the boiler, including switching off, antifreeze, and long-term shutdown.
Guides users through the steps for safely restarting the boiler after shutdown, including initial commissioning.
Lists essential checks and maintenance tasks that should be performed at least once a year for optimal performance.
Details how the boiler's indicator lights signal specific error messages and communication faults.
Provides common operational issues, such as burner not working or cold radiators, with suggested solutions.
Presents detailed technical specifications for the WHE 2.24 and WHE 2.24 FF models, including power, efficiency, and dimensions.
Explains the warranty terms, conditions, exclusions, and responsibilities of the manufacturer, installer, and user.
To Next Page