DEEP SEA ELECTRONICS DSE8610 MKII - Table of Contents

DSE8610 MKII Operator Manual
057-254 ISSUE: 10
Page 4 of 246
TABLE OF CONTENTS
Section
Page
1 INTRODUCTION ................................................................................................ 10
1.1 CLARIFICATION OF NOTATION .......................................................................................... 11
1.2 GLOSSARY OF TERMS ........................................................................................................ 11
1.3 BIBLIOGRAPHY .................................................................................................................... 13
1.3.1 INSTALLATION INSTRUCTIONS ................................................................................... 13
1.3.2 MANUALS ....................................................................................................................... 14
1.3.3 TRAINING GUIDES ........................................................................................................ 15
1.3.4 THIRD PARTY DOCUMENTS ........................................................................................ 16
2 SPECIFICATION ................................................................................................ 17
2.1 PART NUMBERING ............................................................................................................... 17
2.2 OPERATING TEMPERATURE .............................................................................................. 17
2.2.1 SCREEN HEATER OPERATION .................................................................................... 17
2.3 REQUIREMENTS FOR UL .................................................................................................... 18
2.4 TERMINAL SPECIFICATION ................................................................................................ 19
2.5 POWER SUPPLY REQUIREMENTS ..................................................................................... 19
2.5.1 MODULE SUPPLY INSTRUMENTATION DISPLAY ...................................................... 19
2.6 VOLTAGE & FREQUENCY SENSING .................................................................................. 20
2.7 CURRENT SENSING ............................................................................................................. 20
2.7.1 VA RATING OF THE CTS ............................................................................................... 21
2.7.2 CT POLARITY ................................................................................................................. 22
2.7.3 CT PHASING ................................................................................................................... 22
2.7.4 CT CLASS ....................................................................................................................... 22
2.8 INPUTS ................................................................................................................................... 23
2.8.1 DIGITAL INPUTS ............................................................................................................ 23
2.8.2 EMERGENCY STOP ...................................................................................................... 23
2.8.3 ANALOGUE INPUTS ...................................................................................................... 24
2.8.3.1 ANALOGUE INPUT A .............................................................................................. 24
2.8.3.2 ANALOGUE INPUT B, C & D .................................................................................. 25
2.8.4 CHARGE FAIL INPUT ..................................................................................................... 26
2.8.5 MAGNETIC PICK-UP ...................................................................................................... 26
2.9 OUTPUTS ............................................................................................................................... 27
2.9.1 DC OUTPUTS A & B (FUEL & START) .......................................................................... 27
2.9.2 CONFIGURABLE VOLT-FREE RELAY OUTPUTS C & D ............................................. 27
2.9.3 CONFIGURABLE DC OUTPUTS E, F, G, H, I, J, K & L ................................................. 27
2.9.4 GOVERNOR CONTROL OUTPUT ................................................................................. 27
2.9.5 AVR CONTROL OUTPUT ............................................................................................... 27
2.10 COMMUNICATION PORTS ............................................................................................... 28
2.11 COMMUNICATION PORT USAGE .................................................................................... 29
2.11.1 USB SLAVE PORT (PC CONFIGURATION) .................................................................. 29
2.11.2 USB HOST PORT (DATA LOGGING) ............................................................................ 29
2.11.3 RS232 PORT ................................................................................................................... 30
2.11.3.1 RECOMMENDED EXTERNAL MODEMS ............................................................... 30
2.11.3.2 RECOMMENDED PC RS232 SERIAL PORT ADD-ONS ....................................... 31
2.11.3.3 RS232 USED FOR PLC COMMUNICATION .......................................................... 32
2.11.3.4 RS232 USED FOR THE DSE2610 REMOTE DISPLAY ......................................... 33
2.11.4 RS485 PORT ................................................................................................................... 34
2.11.4.1 CABLE SPECIFICATION ......................................................................................... 34
2.11.4.2 RECOMMENDED PC RS485 SERIAL PORT ADD-ONS ....................................... 35
2.11.4.3 RS485 USED FOR MODBUS ENGINE CONNECTION ......................................... 36
2.11.4.4 RS485 USED FOR PLC COMMUNICATION .......................................................... 36
2.11.5 ETHERNET PORT .......................................................................................................... 37
2.11.5.1 MODBUS TCP ......................................................................................................... 37
2.11.5.2 ETHERNET PORT USED FOR PLC COMMUNICATION ....................................... 37
2.11.5.3 SNMP ....................................................................................................................... 38
2.11.5.4 DIRECT PC CONNECTION ..................................................................................... 39