What to do if red indicator light flashes on Defiant Flood Light, but the light does not turn on?
If the red indicator light flashes on your Defiant Flood Light, but the light does not turn on, the LUX setting might be too high. Decrease the LUX setting.
What to do if Defiant Flood Light turns on during the day?
If your Defiant Flood Light is turning on during the day, it might be mounted in a dark or shaded location, or the LUX setting is too high. Decrease the LUX setting.
Why is my Defiant Flood Light dimmer than normal?
If your Defiant Flood Light appears dimmer than normal, the rechargeable Nickel-metal Hydride batteries may be low. Allow the light to charge for 5 hours of continuous sunlight. If the dimness persists and the unit has been in operation for over 1 year, new Ni-MH batteries may be needed.
How to fix Defiant DFI-0654-WH that will not turn on?
If your Defiant Lighting Equipment won't turn on, several factors could be at play. First, ensure the power button is switched on. If that's not the issue, the battery might be depleted; recharge it in direct sunlight. Check the extension cord length between the solar panel and the light fixture; it should be no longer than 60 ft. Also, make sure the solar panel is correctly positioned facing southward for sufficient and direct sunlight. Adjust the SENS dial and LUX setting to compensate for other light sources. Finally, verify the surrounding air temperature is within the specified range of -4°F to 122°F (-20°C to 50°C).
What to do if Defiant DFI-0654-WH light appears to “strobe” or flash?
If your Defiant Lighting Equipment is strobing or flashing, it might be due to a low battery. Turn the light off and charge it in direct sunlight. Another cause can be surrounding light sources affecting the motion sensor. Remove any such sources or relocate the light. You can also try turning the light off for 10 seconds and then back on to resolve a possible program error.
Why does my Defiant DFI-0654-WH turn on during the day?
If your Defiant Lighting Equipment is turning on during the day, it might be mounted in a dark location. Try adjusting the LUX dial towards "L". If the issue persists, relocate the light to a location away from shadows.
What to do if Defiant Lighting Equipment green indicator light continues to flash but the light does not turn ON?
If the green indicator light on your Defiant Lighting Equipment is flashing but the light doesn't turn on, it indicates a program error. To fix this, disconnect and then reconnect the battery to reset the system.
How to fix Defiant Lighting Equipment if the light appears dimmer than normal?
If your Defiant Lighting Equipment light is dimmer than usual, the rechargeable batteries might be low, causing the unit to switch to ECO mode. Once the battery charges back to 3.7V, the light will exit ECO mode and return to normal brightness. Adjusting the TIME dial to a smaller amount of time can also help save battery.
Why Defiant Flood Light will not turn on at night?
There are several reasons why your Defiant Flood Light might not be turning on at night: * The Power button might be in the OFF position. Ensure it is in the ON position. * The batteries may be depleted due to poor charging conditions or extended use (over a year). Check the connection to the solar panel and ensure it receives ample sunlight. New Nickel-metal Hydride batteries can be purchased. * Too many extensions (more than 60 ft.) might be installed. Use fewer cords or reposition the solar panel closer to the light. * The solar panel might not be optimally positioned. Adjust it to face southward for direct sunlight. * The motion sensor may not be detecting motion. Increase SENS and decrease LUX. * Ambient light might be interfering with activation. Increase the LUX setting...
Read manual before use. Mount at 8 ft. high. Do not cut solar wire or immerse in liquid. Ensure secure cord placement.
Product guaranteed free of factory defective parts and workmanship for 3 years from date of purchase.
Covers factory defective parts and workmanship.
Excludes misuse, abuse, negligence, unauthorized service, inconvenience, and loss of use.
Ensure all parts are present before installing. Compare with Hardware Included and Package Contents.
Requires 1-2 days of direct sunlight to fully charge. Aim solar panel South, tilt 50°.
Operates on battery charged by solar panel. Light activates when motion sensor is triggered and battery voltage is above 3V.
Place solar panel for maximum direct sunlight, ideally facing South or on the highest point of a structure.
Main unit has LEDs, motion sensor, rechargeable batteries. Sensor has 50 ft. range and 180° detection angle.
Details range (50 ft.), sensing angle (180°), lumens (1000 LM), power, operating modes, and time delay.
Lists safety goggles, Phillips screwdriver, drill bits, drill, level, and ladder for installation.
Lists parts like mounting plate, screws, anchors, and bolts with quantities for installation.
Details components like lamp head, light fixture, motion sensor, solar panel, and cords with quantities.
Mount fixture approx. 8 ft. high. Ensure fixture and solar panel are close enough. Solar panel must face South.
Adjust motion sensor angle for desired coverage; tilt downward or side-to-side for wall mount, outward or side-to-side for eave mount.
Mount the plate level, mark holes, drill pilot holes, and secure with screws/anchors depending on surface.
Slide fixture onto mounting plate and secure with mounting bolts from the sides.
Mount solar panel base, attach panel, adjust angle and direction for optimal sunlight.
Rotate the solar panel to the desired angle for optimal sunlight exposure.
Connect solar panel cable to light fixture, screw caps firmly. Form a drip loop. Turn switch OFF for charging.
Grasp lamp heads and tilt them up/down or side-to-side to adjust light coverage.
Press Power button (D) to turn light off. Pushing in turns ON (AUTO), pushing out turns OFF.
Test LEDs and sensor in 'Test' mode. Adjust lamp heads and sensor. Switch to 'Motion' for normal operation.
Indicator light shows status: RED flashes for motion detection, GREEN for battery charging.
TIME dial controls how long light stays on after motion. Adjustable from 30 to 90 seconds.
LUX dial adjusts brightness to trigger dusk-to-dawn. 'L' for dark areas, 'H' for daylight activation.
SENS dial adjusts motion sensor sensitivity and range. 'H' for max sensitivity/range up to 50 ft., 'L' for less.
Replace three AA, 2000 mAh Ni-MH batteries. Disconnect, unmount, remove back panel, replace batteries, and reassemble.
Clean fixture with water and soft cloth. Clean solar panel with soft cloth and warm water. Avoid chemicals and pressure washing.
Check Power button, battery charge, solar panel connection, sunlight exposure, and extensions.
Sensor is detecting motion but light is not activating. Check LUX and SENS settings.
Indicates LUX setting is too high or unit is mounted in shaded/dark location. Decrease LUX setting.
Batteries may be low. Allow charging time or consider replacing Ni-MH batteries.
General| Brand | Defiant |
|---|---|
| Model | DFI-0654-WH |
| Voltage | 120 V |
| Material | Plastic |
| Finish | White |
| Dimmable | No |
| Light Bulb Base Code | Integrated LED |
| Bulb Type | LED |
| Energy Star Certified | Yes |
| Life Hours | 50, 000 hours |
To Next Page
