EasyManuals Logo

Denon AVR-X3300W User Manual

Denon AVR-X3300W
296 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #224 background imageLoading...
Page #224 background image
o
Add New Feature
Display new features that can be downloaded to this unit and perform
an upgrade.
Upgrade Package: Display the items to be upgraded.
Upgrade Status:
Display a list of the additional functions
provided by the upgrade.
Upgrade Start:
Execute the upgrade process.
When the upgrade starts, the menu
screen is shut down. During the upgrade,
the amount of upgrade time which has
elapsed is displayed.
0
See the Denon website for details about upgrades.
0
When the procedure is complete, “Registered” is displayed in this menu and
upgrades can be carried out. If the procedure has not been carried out, “-------”
is displayed.
The ID number shown on this screen is needed when carrying out the
procedure.
The ID number can also be displayed by pressing and holding the main unit’s
TUNER PRESET CH - and STATUS for at least 3 seconds.
0
If the upgrade is not successful, an error message identical to those in
“Firmware” - “Update” will appear on the display. Check the settings and
network environment and then perform the upgrade again.
Notes concerning use of “Update” and “Add New Feature”
0
In order to use these functions, you must have the correct system
requirements and settings for an Internet connection. (v
p. 61)
0
Do not turn off the power until updating or upgrading is completed.
0
Approximately 1 hour is required for the updating/upgrading procedure
to be completed.
0
Once updating/upgrade starts, normal operations on this unit cannot
be performed until updating/upgrading is completed. Furthermore,
there may be cases where backup data is reset for the parameters,
etc., set on this unit.
0
If the update or upgrade fails, press and hold the X on the main unit for
more than 5 seconds, or remove and re-insert the power cord. “Update
Retry” appears on the display and update restarts from the point at
which update failed. If the error continues despite this, check the
network environment.
0
Information regarding the “Update” function and “Add New Feature” will be
announced on the Denon website each time related plans are defined.
Contents Connections Playback Settings Tips Appendix
224
Front panel Display Rear panel Remote Index

Table of Contents

Other manuals for Denon AVR-X3300W

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X3300W and is the answer not in the manual?

Denon AVR-X3300W Specifications

General IconGeneral
Receiver typeSurround
Frequency range10 - 100000 Hz
Pre-out channels7.2
Pre-out connectivityYes
Audio output channels7.2 channels
Signal-to-Noise Ratio (SNR)100 dB
Total Harmonic Distortion (THD)0.05 %
Power output per channel (1KHz@6 Ohm)180 W
Power output per channel (20-20KHz@8 Ohm)105 W
AC input voltage230 V
AC input frequency50 Hz
Power consumption (standby)0.1 W
Power consumption (typical)600 W
Product colorBlack
Audio decodersDTS-HD, DTS-HD Master Audio, Dolby TrueHD
Multi-Zone quantity2
Apple docking compatibility-
AM band range522 - 1611 kHz
FM band range87.5 - 108 MHz
Supported radio bandsAM, FM
HDMI in8
Audio (L/R) in5
Remote control in1
Composite video in3
Composite video out0
Connectivity technologyWired
Speakers connectivity typeClamp terminals
Audio formats supportedAAC, AIFF, ALAC, DSD, FLAC, MP3, WAV, WMA
Weight and Dimensions IconWeight and Dimensions
Depth389 mm
Width434 mm
Height167 mm
Weight10800 g

Related product manuals