Denon DN-951FA - Page 16

9}
d2-7
{d3-1]
(43-2)
FRAME DISPLAY Of:
* [I]:
iNITIAL DISPLAY 0):
a
END DETECT Ol:
* (1):
RE CUE * [Ql]:
ui:
PLAY LOCK * (0):
Uy:
FLASH Oj:
* {7
REMOTE INHIBIT * {0}:
Ale
SWITCH INHIBIT * [0]:
Us
Frame not displayed during playback.
Frame dispiayed during playback.
Elapsed time displayed when power turned on.
Remaining time displayed when power turned on.
Track ends not detected during search operation.
Track ends detected during search operation.
Stap mode set when playback ends.
When playback ends, pickup returns to starting position and standby mode set.
Buttons other than the ones below also function during playback.
Buttons other than the PLAY MODE, TIME, PLAY/PAUSE and RESET buttons
do not function during playback.
PLAY indicator remains turned off (without flashing) during EOM operation,
PAUSE indicator remains turned off when playback 2nds, and STDBY/CUE
indicator remains turned off during search operation.
PLAY indicator flashes during EOM operation, PAUSE indicator flashes when
playback ends, and STDBY/CUE indicator flashes during search operation.
“REMOTE” command accepted.
“REMOTE” command not accepted.
No front panel buttons other than PLAY MODE, TIME and RESET buttons function.
Ail buttons function.
[d3-3, 4 and 5] £.0.M.: (PLAY/PAUSE button flashes green)
(d3-8]
(d4-1]
{d4-2]
(d4-5, 6]
(d4-7}
{d3-3}
0
-~o~o+-oO-
DIGITAL OUT * [0]:
a)
TEST * [0]:
VARIABLE SPEED ENABLE
* [0]:
(1):
DELAY START:
{d4-5}
* 0
1
0
1
COR DISC * (9):
(1:
{d3-4] {d3-5} £.0.M. time setting
i) 0 £.0.M. not output
(0) 5 sec
0 10 sec
0 15 sec
1 20 sec
1 25 sec
1 30 sec
1 1 35 sec
Standard playback mode.
Oniy audio data output from digital output.
Digital output priority mode.
Audio data and subcodes output from digital output.
OSP functions (FADE IN, MONO) inhibited.
-~oo+-+0
Standard playback mode. {Always leave this at [O|, The player cannot be used
if set to (1}.)
Discs played at standard speed.
Discs played at speed set by variable speed presetting [d6-1, 2, 3 and 4j.
{d4-6] Delay start time setting
0 0 msec
0 100 msec
1 200 msec
1 300 msec
Mode for playing normai discs including TOCs. (Discs without TOCs cannot be played.)
Discs recorded on a CD recorder (DN-7700R, etc.} without TOCs can be played.
{d4-8]
[d5-3]
(d5-4}
NEXT TRACK STANDBY
* [0]:
1h:
§NDEX INHIBIT * [O)}:
1:
INDEX 3/2 Oj:
* (1):
EOM/INDEX * {0}:
Tle:
rADER START MODE SELECT
(01:
* (1:
{d5-5, 6 and 7} END MONITOR:
[d5-8}
INDEX 2
(d5-5]
0
-o-o-4048
* (0h:
{1}:
When playback ends, next operation performed according to “RE CUE" setting.
When playback ends, standby mode set at next track. (“RE CUE” setting ignored.)
Index numbers can be selected.
index numbers cannot be selected.
"INDEX 2 TALLY” output from REMOTE connector pins 24 and 25.
(Not valid when {d5-3] set to [1].)
"INDEX 3 TALLY” output from REMOTE connector pins 24 and 25.
(Not valid when {d5-3] set to [1].)
“INDEX TALLY” {set by INDEX 3/2 [d5-2]) output from REMOTE connector
pins 24 and 25.
“EOM TALLY” output from REMOTE connector pins 24 and 25.
Player starts when fader switch turned on.
Piayer starts when fader switch turned on, set to pause mode when fader
switch turned off.
[d5-6] (d5-7] End monitor time setting
0 Q End monitor off.
5 sec
10 sec
15 sec
20 sec
25 sec
30 sec
1 1 35 sec
“INDEX 3 TALLY” output from REMOTE connector pin 17.
“INDEX 2 TALLY” output fromm REMOTE connector pin 17.
=eo-4+0
-44 000
[d6-1, 2, 3 and 4) VARIABLE SPEED: This sets the piaying speed within a range of 0 to 3% when (d4-2] is set to [1].
[d6-5]
{d6-61
SKIP TRACK
END MARK
{d6-1}
0
~onwOoO~O+-O-0270-+06
{0}:
* (0):
Oh:
(d6-2] {d6-3] {06-4]
0 0 0
Playback speed
0.0% {Standard speed)
+0.2%
+0.4%
+0.6%
+0.8%
+1.0%
+1.2%
4+1.4%
+1.6%
+1.8%
+2.0%
+2.2%
+2.4%
+2.6%
72.8%
1 1 1 +3.0%
Skip track playback as set in the TOC is possible when playing COR discs.
Skip track playback as set in the TOC is not possible when playing CDR discs.
The track end position does not change even if the PLAY/PAUSE button is pressed
during the end monitor mode.
The position at which the PLAY/PAUSE button is pressed during the end monitor
function becomes the track end position.
~aeaewr esr acoco0c00 =~eo-s-004400--0 -s-2s0000-42-5000
SS a a een VAL OS/VALSGG-NO &