What to do if my Denon CD Player has no sound or picture?
If your Denon CD Player isn't producing any sound or picture, make sure your TV is turned on. Also, check the video connection and HDMI cables, as well as the VIDEO/AUDIO cable connections to the TV. Ensure that the PURE DIRECT setting is OFF, and verify that the PROGRESSIVE mode is set correctly.
Why is there no sound coming from my Denon CD Player or the sound is distorted?
If you are getting no sound or distorted sound from your Denon CD Player, first adjust the volume. Next, check that the speakers are connected correctly. Note that HDMI sound is not output during PURE DIRECT or when AUDIO MODE is set to ANALOG.
What to do if my Denon CD Player remote control is not working?
If your Denon CD player is not responding to the remote control, aim the remote directly at the sensor on the front of the player. Try reducing the distance to the player. If the issue persists, replace the batteries in the remote, ensuring they are inserted with the correct polarities (+/– signs).
How to fix no image from HDMI connection on Denon CD Player?
If you are not getting an image from the HDMI connection on your Denon CD player, first check the HDMI connection itself. Ensure that the connected monitor or equipment supports HDCP. If not, the player will not output a video signal. You can also connect the player to the display device using the Audio/Video cables and check the HDMI settings. Verify that the output format of the player (HDMI FORMAT) matches the supported input format of the connected equipment and check if the PURE DIRECT is set to ON, and if it is, set it to OFF.
What to do if Denon CD Player buttons do not work or it stops responding?
If your Denon CD Player buttons do not work or the player stops responding, unplug the AC cord from the AC outlet for 5-10 seconds to completely reset the player.
Why does the picture freeze momentarily during playback on my Denon CD Player?
If the picture freezes momentarily during playback on your Denon CD Player, inspect the disc for fingerprints or scratches. Clean the disc with a soft cloth, wiping from the center to the edge.
What to do if my Denon CD Player disc cannot be played?
If your Denon CD Player cannot play a disc, start by cleaning the disc. Make sure the disc label is facing up. Try another disc to check if the original disc is defective. Also, check if Ratings control is enabled and cancel it or change the control level. Ensure that you are inserting a disc that is compatible with the player.
How do I fix a Denon DVD-1930CI that cannot read CDs/DVDs?
Use a commonly available CD/DVD cleaner to clean the lens of your Denon DVD player before sending it for repair.
How to troubleshoot a Denon CD Player with no power?
If your Denon CD Player is not getting power, verify that the AC power cord is properly connected. If it is, unplug the cord, wait 5-10 seconds, and then plug it back in.
Why is there no audio at digital output on my Denon CD Player?
If you are getting no audio at the digital output of your Denon CD Player, check the digital connections and the audio settings. Digital signals cannot be output with Super Audio CDs, so use analog connections instead. Also, the area/layer of Super audio CD being played (MULTI/STEREO/CD) does not match amplifier connections.
Audio Specifications| frequency response (DVD) | 4 Hz - 22 kHz (48kHz sampling), 4 Hz - 44 kHz (96kHz sampling), 4 Hz - 88 kHz (192kHz sampling) |
|---|---|
| frequency response (CD) | 4 Hz - 20 kHz |
| frequency response (Super Audio CD) | 4 Hz - 100 kHz |
| signal-to-noise ratio | 115 dB |
| dynamic range (DVD) | 100 dB |
| dynamic range (CD) | 98 dB |
| total harmonic distortion (1 kHz CD) | 0.004% |
Video Specifications| signal system | NTSC |
|---|---|
| composite video output | 1.0 Vp-p (with 75 ohms load) |
| S-Video output (Y) | 1.0 Vp-p (with 75 ohms load) |
| S-Video output (C) | 0.286 Vp-p |
| component video output (Y) | 1.0 Vp-p (with 75 ohms load) |
| component video output (Pb/Cb) | 0.648 Vp-p (with 75 ohms load) |
| component video output (Pr/Cr) | 0.648 Vp-p (with 75 ohms load) |
| HDMI Output | ver1.1 |
General Specifications| power supply | AC 120 V, 60 Hz |
|---|---|
| power consumption | 15 W |
| power consumption (standby) | 1 W |
| dimensions | 435 (W) x 75 (H) x 310 (D) mm |
| dimensions (inches) | 17-3/32” (W) x 2-61/64” (H) x 12-13/64” (D) |
| weight | 2.6 kg |
| weight (lbs) | 5.72 lbs |
To Next Page
