Why is my Denon DVD-2910 DVD Player remote not working?
If the Denon DVD Player remote control isn't working, first ensure the batteries are correctly inserted with the proper polarity. If they are dead, replace them with new ones. Make sure to point the remote directly at the sensor within 7 meters, and remove any obstacles that might be blocking the signal.
What to do if there is no picture on my Denon DVD-2910?
If you're not getting a picture on your Denon DVD Player, check all the connections first. Ensure that the VIDEO OUT setting is not set to “VIDEO OUT:OFF” or “ALL OFF” for PURE DIRECT MODE. Also, make sure your TV’s input is set to “video.” If using HDMI or DVI-D, progressive signals from the component video connector will be disabled; set HDMI/DVI SELECT to “OFF” if you want to use the component video output.
How to fix sound issues with my Denon DVD Player?
If your Denon DVD Player isn't producing sound or the sound quality is poor, start by checking all the connections. Ensure the input of your TV or stereo is properly set. Review the “DIGITAL OUTPUT” and “COMPRESSION” settings. Note that digital signals cannot be output with Super audio CDs, so use analog connections for those. Ensure the area/layer of the Super audio CD being played matches your amplifier connections. Also, if the video output setting at “PURE DIRECT” is set to “VIDEO : OFF” or “ALL OFF”, there will be no sound at the HDMI connector.
What to do if Denon DVD-2910 playback stops or doesn't start?
If your Denon DVD Player doesn't start playback when you press the PLAY button, or if playback stops immediately, check if there's condensation on the disc or player; if so, let it stand for 1 or 2 hours. Ensure you're using a compatible disc (DVD, SuperAudio CD, video CD, or music CD). Finally, check if the disc is dirty and, if so, wipe it clean.
Why is there no image with HDMI/DVI on my Denon DVD-2910?
If you're not getting an image with an HDMI/DVI connection on your Denon DVD Player, verify the HDMI/DVI connection and check the status of the HDMI/DVI-related indicators. Confirm that your monitor or other connected equipment supports HDCP. Also, check the “HDMI/DVI SELECT” settings and ensure the output format of the DVD Player matches the supported input format of the connected equipment. Finally, check if the video output setting at “PURE DIRECT” is set to “VIDEO: OFF” or “ALL OFF.”
How to turn on subtitles on Denon DVD-2910 DVD Player?
If subtitles are not showing on your Denon DVD Player, it could be that the DVD does not contain subtitles. Also, check if the subtitle setting is turned off and, if so, turn it on.
How to adjust aspect ratio on Denon DVD-2910?
If the picture on your Denon DVD Player isn't displayed in the correct 4:3 or 16:9 aspect ratio, set the “TV ASPECT” default setting to the proper setting for your connected TV.
Why can't I change the language on my Denon DVD Player?
If the audio or subtitle language isn't switching on your Denon DVD Player, it may be that the disc doesn't include multiple audio or subtitle languages. For some discs, you may need to switch the language on the menu screens rather than during playback.
How to reset parental control password on Denon DVD-2910 DVD Player?
If you've forgotten the password for the rating level on your Denon DVD Player, while the player is in stop mode, hold the player’s SKIP 9 button and the PLAY button down simultaneously, then hold the OPEN/CLOSE button down for longer than 3 seconds (until “INITIALIZE” disappears from the TV monitor). This will release the lock and return all settings to default.
How to change the menu language on Denon DVD Player?
If the menu screen messages for your desired language aren't displaying on your Denon DVD Player, check the default setting for the disc language’s menu language.
Check leakage current or line-to-chassis resistance before returning the unit.
Precautions regarding laser safety during operation and servicing.
Troubleshooting steps for various disc read failures.
Diagnosing and resolving audio output issues.
Detailed circuit diagrams for the main unit, part 1 of 4.
Detailed circuit diagrams for the video unit, part 1 of 4.
Detailed circuit diagram for the audio unit.
General| Progressive Scan | Yes |
|---|---|
| Output Video Resolution | 480i, 480p, 720p, 1080i |
| Video DAC | 216MHz/12-bit |
| Surround Sound | Dolby Digital, DTS |
| HDMI Output | Yes |
| Component Video Output | Yes |
| S-Video Output | Yes |
| Composite Video Output | Yes |
| Digital Audio Output | Coaxial, Optical |
| Playback Formats | DVD Video, CD, SACD, MP3, JPEG |
| Video Upconversion | Yes (720p, 1080i) |
| Audio DAC | 24-bit/192kHz |
| Analog Audio Output | 2 channel, 5.1 channel |
To Next Page
