www.desatech.com
113170-01E 5
T
e
m
p
e
r
at
ur
e
T
e
m
p
e
r
a
t
ur
a
Th
er
m
os
t
a
t
T
e
r
m
o
s
t
a
t
o
LO
H
I
I
g
n
i
t
or
•
E
n
c
en
d
e
d
o
r
Allu
m
e
u
r
V
o
l
t
a
g
e
•
T
e
n
s
i
ó
n
•
T
e
n
s
io
n
F
l
a
m
e
•
L
l
a
m
a
•
F
l
a
mm
e
S
t
a
r
t
/
R
u
n
E
n
c
i
e
n
d
a
/
O
p
e
ra
c
i
ó
n
D
é
m
ar
r
e
/
M
a
r
c
h
e
5
6
4
3
2
1
Figure 3 - Wheel and Handle Assembly
Axle
Extension
Cord Wrap
Air Inlet
Rear Panel
Hot Air Outlet
Wheel
Handle
Screw
Washer
Extended Hub
Washer
Cap Nut
Shroud
Axle Hole
ASSEMBLY
Continued
Shroud
OPERATION
IMPORTANT: Review and under-
stand the warnings in the Safety
Information section, page 2.
They are needed to safely oper
-
ate this heater. Follow all local
ordinances and codes when
using this heater.
TO START HEATER
1. Follow all ventilation and safety information.
2. Locate heater to provide maximum circulation
of the heated air. Follow all location require-
ments noted in Safety Information, page 2.
3. Fill fuel tank with fuel. Use only kerosene,
#1/#2 diesel/fuel oil, JET A or JP-8 fuels to
avoid risk of fire or explosion. Never use
gasoline, naphtha, paint thinners, alcohol or
other flammable fuels.
4. Attach fuel cap/gauge.
5. Plug heaterʼs power cord into approved,
grounded, three-wire extension cord. Extension
cord must be at least six feet (1.8 meters) long.
Extension Cord Size Requirement
6 to 10 feet (1.8 to 3 meters) long, use 18 AWG
(0.75 mm
2
) rated cord
11 to 100 feet (3.3 to 30.5 meters) long, use
16 AWG (1.0 mm
2
) rated cord
101 to 200 feet (30.8 to 61 meters) long, use
14 AWG (1.5 mm
2
) rated cord
6. Plug extension cord into standard 120 volt/60
hertz, 3-prong grounded outlet.
7. Turn thermostat knob to the right (clockwise)
to the warmest position.
8. Push ON/OFF switch to the ON (|) position.
Light will come on. Note: Ignitor will preheat
for five seconds, then heater will start.
9. After heater is running, adjust thermostat knob
to the desired setting. Note: A cold heater may
affect the thermostat setting. This thermostat is
a general-heating control. It is not intended for
precise temperature control. Adjust thermostat
until heater cycles at the desired setting.
TO STOP HEATER
1. Push ON/OFF switch to the OFF (O) position.
2. Unplug heater.
TO RESET HEATER
1. Push ON/OFF switch to the OFF (O) position
and wait 10 seconds. (Wait two minutes if
heater has been running.)
2. Repeat steps under To Start Heater
.
Wheel
Spacer
To Next Page
Loading...
Need help?
General
