Safety Information
4 / 268 06/2021
Model rpm
EFD80-950 103
EFDO24-20 1940
EFDO30-80 900
EFDO40-180 560
EFDO54-450 230
Weight
Model kg lb
EFD43-8 1.85 4.08
EFD43-15 1.85 4.08
EFD43-30 2.3 5.07
EFD43-45 2.3 5.07
EFD51-70 3.95 8.7
EFD51-135 3.95 8.7
EFD60-175 5.3 11.7
EFD60-250 5.3 11.7
EFD80-330 9.9 21.8
EFD80-450 9.9 21.8
EFD80-680 9.9 21.8
EFD80-950 9.9 21.8
EFDO24-20 3.1 6.83
EFDO30-80 5.5 12.12
EFDO40-180 8.8 19.40
EFDO54-450 17.2 37.92
Storage and use conditions
Storage temperature -20 to +70 °C (-4 to +158 F)
Operating temperature 0 to 45 °C (32 to 113 F)
Storage humidity 0-95 % RH (non-condensing)
Operating humidity 0-90 % RH (non-condensing)
Altitude up to 2000 m (6562 feet)
Usable in Pollution degree 2
environment
Indoor use only
Declarations
Liability
Many events in the operating environment may affect the
tightening process and shall require a validation of results. In
compliance with applicable standards and/or regulations, we
hereby require you to check the installed torque and rota-
tional direction after any event that can influence the tighten-
ing result. Examples of such events include but are not lim-
ited to:
• initial installation of the tooling system
• change of part batch, bolt, screw batch, tool, software,
configuration or environment
• change of air- or electrical connections
• change in line ergonomics, process, quality procedures
or practices
• changing of operator
• any other change that influences the result of the tighten-
ing process
The check should:
• Ensure that the joint conditions have not changed due to
events of influence.
• Be done after initial installation, maintenance or repair
of the equipment.
• Occur at least once per shift or at another suitable fre-
quency.
EU DECLARATION OF INCORPORATION
AND EU DECLARATION OF CONFORMITY
We Ets Georges Renault, 38 rue Bobby Sands, 44818 Saint
Herblain, France, declare under our sole responsibility that
this product (with name, type and serial number, see front
page) fulfills the following essential requirements of Machin-
ery Directive 2006/42/EC, and must not be put into service
until the final machinery, into which it is to be incorporated,
has been declared in conformity with that Directive. It is in
conformity with the following Directive(s):
2006/42/EC, 2014/30/UE, 2011/65/EU
Harmonized standards applied:
EN 62841-2-2 :2014, EN 61000-6-2 :2005+C1 :2005, EN
61000-6-4 :2007+A1 :2011, Class A/Industrial,
EN61326-2-3 :2013
The relevant technical documentation was compiled and was
communicated in accordance with Machinery Directive
2006/42/EC part B of Annex VII. Authorities can request the
relevant technical information from:
Pascal ROUSSY, R&D Manager, 38 rue Bobby Sands,
44818 Saint Herblain, France
Saint-Herblain, 2020/11/13
Pascal ROUSSY, R&D Manager
Signature of issuer
Noise and Vibration Declaration Statement
• A-weighted emission sound pressure level LpA in
dB(A) , uncertainty 3 dB(A) in accordance with EN
62841-2-2 : 2014
• A-weighted sound power level LWA in dB(A), uncer-
tainty 3 dB(A) in accordance with EN 62841-2-2 : 2014
Model LpA LWA
EFD43-8 < 70 < 80
EFD43-15 < 72 < 83
EFD43-30 < 70 < 80
To Next Page
Loading...
