DeWalt DCB104 Original Instructions

12 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

DCB104

Final page size: A5 (148mm x 210mm)

Table of Contents

Other manuals for DeWalt DCB104

Instruction Manual24 pages

Questions and Answers:

T
Tony LarsonAug 17, 2025
What to do if the regulator is not adjusted correctly on my DeWalt Air Compressor?
- T
  thompsonmaryAug 17, 2025
  If the regulator on your DeWalt Air Compressor isn't correctly adjusted for the accessory you're using, and there's excessive pressure drop, adjust it as instructed in One-turn Regulator under Description of Operations. It’s normal for some pressure drop to occur when using an accessory. Make sure to adjust the regulated pressure under flow conditions while the accessory is in use.
M
Matthew LewisAug 20, 2025
What to do if motor overload protection switch has tripped in DeWalt Air Compressor?
- B
  Brandon RamosAug 20, 2025
  To address the issue where the motor overload protection switch has tripped on your DeWalt Air Compressor, refer to Motor Overload Protector under Description of Operations. If the motor overload protection trips frequently, contact a DeWALT factory service center or a DeWALT authorized service center.
C
Carla PerryAug 22, 2025
What to do if pump does not run because tank pressure is above cut-in pressure on DeWalt Air Compressor?
- R
  Robert Taylor MDAug 22, 2025
  If your DeWalt Air Compressor pump isn't running because the tank pressure is above the cut-in pressure, drain the tank until the pressure drops below the cut-in point. The pump should then turn on.
W
walkerlisaAug 25, 2025
What to do if pump does not run due to safety fault on DeWalt Air Compressor?
- K
  Kathy HawkinsAug 26, 2025
  To resolve a situation where the pump on your DeWalt Air Compressor isn't running due to a safety fault, cycle the Auto On/Off Switch from the "Off" position to "Auto On."
L
Laura ReedAug 28, 2025
What to do if pressure switch does not shut off motor on DeWalt Air Compressor?
- C
  Christina CortezAug 28, 2025
  If the pressure switch on your DeWalt Air Compressor doesn't shut off the motor when it reaches the cut-out pressure, set the Auto On/Off switch to "Off" and remove the battery, if the unit does not shut off contact a DeWALT factory service center or a DeWALT authorized service center.
J
Jennifer KellyAug 30, 2025
What to do if regulator is damaged on DeWalt Air Compressor?
- S
  smitchellAug 31, 2025
  If the regulator on your DeWalt Air Compressor is damaged, it should be replaced.
T
Timothy JohnsonSep 2, 2025
How to fix air leaking from tube fittings on DeWalt Air Compressor?
- R
  Rebecca WalkerSep 2, 2025
  If you hear air escaping from tube fittings on your DeWalt Air Compressor, tighten the fittings until the leak stops. You can use soapy water to help find the exact spot. Be careful not to overtighten them.
K
karen33Sep 5, 2025
What to do if safety valve is defective on DeWalt Air Compressor?
- J
  Joshua BrownSep 5, 2025
  If the safety valve on your DeWalt Air Compressor is defective, manually operate it by pulling on the ring. If the valve continues to leak after doing this, it needs to be replaced.
A
andrewjacksonSep 8, 2025
What to do for prolonged excessive use of air with DeWalt Air Compressor?
- S
  Sara PhelpsSep 8, 2025
  If your DeWalt Air Compressor is experiencing prolonged excessive use of air, decrease the amount of air you are using.

DeWalt DCB104 Specifications

General

Quantity per pack	1 pc(s)

Related product manuals

Preview: DeWalt DCB103

Preview: DeWalt DCB100

Preview: DeWalt DCB107

Preview: DeWalt DCB101

Preview: DeWalt DCB102

Preview: DeWalt DCB115

Preview: DeWalt DCB118

Preview: DeWalt DCB1800

DeWalt DCB1102MDR

DeWalt DCB115 Series

Preview: DeWalt XR Li-Ion DCB118

DeWalt XR Li-Ion DCB118

Preview: DeWalt XR LI-ION DCB115

DeWalt XR LI-ION DCB115