DeWalt DCCS670 User Manual

ENGLISH
15

WARNING: Sharp moving chain. To prevent
accidental operation, ensure that battery is removed
from the tool before performing the following
operations. Failure to do this could result in serious
personalinjury.
NOTE: The cutters will dull immediately if they touch the
ground or a nail whilecutting.
To get the best possible performance from your chain saw
it is important to keep the teeth of the chain sharp. Follow
these helpful tips for proper saw chain sharpening:
1. For best results use a 4.5mm file and a file holder or
filing guide to sharpen your chain. This will ensure you
always get the correct sharpeningangles.
2. Place the file holder flat on the top plate and depth
gauge of thecutter.
3. FigureW- Keep the correct top plate
19
filing angle
line of 30° on your file guide parallel with your chain (file
at 60° from chain viewed from the side).
4. Sharpen cutters on one side of the chain first. File from
the inside of each cutter to the outside. Then turn your
saw around and repeat the processes (2, 3, 4) for cutters
on the other side of thechain.
NOTE: Use a flat file to file the tops of the rakers (portion
of chain link in front of the cutter) so they are about
.025" (.635 mm) below the tips of the cutters as shown
in FigureX.
5. FigureY- Keep all cutter lengthsequal.
6. If damage is present on the chrome surface of the
top plates or side plates, file back until such damage
isremoved.

CAUTION: After filing, the cutter will be sharp, use
extra caution during thisprocess.
NOTE: Each time the chain is sharpened, it loses some of
the low kickback qualities and extra caution should be used.
It is recommended that a chain be sharpened no more than
fourtimes.
60°
Fig. W
19
.025"
(0.635mm)
Fig. X
Fig. Y
Accessories

WARNING: The use of accessories not recommended
in this manual may behazardous.
Replacement chain and bar are available from your nearest
DeWALT authorized service center. For use only with low
kick back bar andchain.
Available bars and chains for DCCS670:
Bar: 16” service part number 90641855
18” service part number N500117
Chain: 16” service part number 90618541
18” service part number N500152
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performingthis.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into aliquid.
Accessories

WARNING: Since accessories, other than those
offered by DeWAL T, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only
DeWAL T
recommended accessories should be used with
thisproduct.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact
DeWALT Industrial
Tool Co., 701East Joppa Road, Towson, MD 21286, call
1-800-4-DeWALT (1-800-433-9258) or visit our website:
www.dewalt.com.
Repairs
The charger and battery pack are notserviceable.

DeWalt DCCS670 Specifications

General

Bar Length	16 inches
Power Source	Battery
Battery Voltage	60 V
Chain Pitch	3/8 inch
Automatic Oiler	Yes
Tool-Free Chain Tensioning	Yes
Battery Compatibility	DeWalt 60V FlexVolt
Chain Speed	25.2 m/s
Weight	12.2 lbs (without battery)
Chain Gauge	0.043 inch