DeWalt DCD790 - Page 18

ENGLISH
18
EC-Declaration of Conformity
Machinery Directive
Drill/Driver/Impact Drill
DCD790, DCD795
DeWALT declares that these products described under
Technical Data are in compliance with:
2006/42/EC, EN62841-1:2015+AC:2015, EN62841-2-1:2018
+A11:2019.
These products also comply with Directive 2014/30/EU and
2011/65/EU. For more information, please contact DeWALT at
the following address or refer to the back of themanual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf ofDeWALT.
Markus Rompel
Vice-President Engineering, PTE-Europe
DeWALT, Richard-Klinger-Straße 11,
65510, Idstein, Germany
29.11.2021
DECLARATION OF CONFORMITY
THE SUPPLY OF MACHINERY SAFETY REGULATIONS
2008
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment ofexposure.
English (original instructions)
BRUSHLESS CORDLESS COMPACT 13 mm
DRILL/DRIVER/IMPACT DRILL
DCD790, DCD795
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough
product development and innovation make DeWALT one of the
most reliable partners for professional power toolusers.
Technical Data
DCD790 DCD795
Voltage V
DC
18 18
Type 3/12 3/12
Battery type Li-Ion Li-Ion
No-load speed
1st gear min
-1
0–600 0–600
2nd gear min
-1
0–2000 0–2000
Impact rate
1st gear min
-1
– 0–10200
2nd gear min
-1
– 0–34000
Max. torque (hard/soft) Nm 60/23 60/23
Chuck capacity mm 1.5–13.0 1.5–13.0
Maximum drilling capacity
Wood mm 38 38
Metal mm 13 13
Masonry mm – 13
Weight (without battery pack) kg 1.20 1.27
Noise values and/or vibration values (triax vector sum) according to
EN62841-2-1:
L
PA
(emission sound pressure level) dB(A) 69 90
L
WA
(sound power level) dB(A) 80 101
K (uncertainty for the given sound
level)
dB(A) 5 3
Drilling into metal
Vibration emission value a
h,D
= m/s
2
2.6 3.1
Uncertainty K = m/s
2
1.5 1.5
Drilling into concrete
Vibration emission value a
h,ID
= m/s
2
– 14
Uncertainty K = m/s
2
– 1.7
Screwdriving
Vibration emission value a
h,D
= m/s
2
<2.5 <2.5
Uncertainty K = m/s
2
1.5 1.5

WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However if the
tool is used for different applications, with different accessories or
poorly maintained, the vibration and/or noise emission may differ.
This may significantly increase the exposure level over the total
workingperiod.
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the job.
This may significantly reduce the exposure level over the total
workingperiod.
Identify additional safety measures to protect the operator from
the effects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm (relevant for vibration),
organisation of workpatterns.