DeWalt DCD792 - Low Battery Warning; Assembly and Adjustments

ENGLISH
9
Dual Range Gearing (Fig.D–F, J)

WARNING: Tool Connect™ allows for the speed of
the drill to be configured to values lower than the
rating on the tool label. If you are unsure of the current
configuration, press the selector mode button
12
(FigJ) to set the tool to the Home setting as described
on the label and thismanual.
The dual range feature of your drill/driver allows you to shift
gears for greaterversatility.
1. To select speed 1 (high-torque setting), turn the tool off
and permit it to stop. Slide the gear shifter
4
forward
(towards the chuck).
2. To select speed 2 (low-torque setting), turn the tool off
and permit it to stop. Slide the gear shifter back (away
from the chuck).
NOTE: Do not change gears when the tool is running.
Always allow the drill to come to a complete stop before
changing gears. If you are having trouble changing
gears, make sure that the dual range gear shifter is either
completely pushed forward or completely pushedback.
Gear speed settings are preset at the factory but can be
customized using the Tool Connect™ app. Refer to Mode
Selector table for factorypresets.
Worklight (Fig.A)

CAUTION: Do not stare into worklight. Serious eye
injury couldresult.
The worklight
5
located on the foot of the tool is activated
when the trigger switch is depressed. In the Home
setting, when the trigger is released, the worklight will
stay illuminated for up to 20 seconds. If the trigger switch
remains depressed, the worklight will remain on. Worklight
settings can be customized using the Tool Connect™app.
Worklight settings can be customized using the Tool
Connect™app. Refer to ModeSelector.
Spotlight Mode
The high setting is the spotlight mode. The spotlight will
run for 20 minutes after the trigger switch is released. Two
minutes before the spotlight will shut off, it will flash twice
and then dim. To avoid the spotlight shutting off, lightly tap
the triggerswitch.

WARNING: While using the worklight in medium
or spotlight mode, do not stare at the light or
place the drill in a position which may cause
anyone to stare into the light. Serious eye injury
couldresult.

CAUTION: When using the tool as a spotlight, be sure
it is secured on a stable surface where it will not cause
a tripping or fallinghazard.

CAUTION: Remove all accessories from the chuck
before using the drill as a spotlight. Personal injury or
property damage couldresult.
Low Battery Warning
When in spotlight mode and the battery is nearing
complete discharge, the spotlight will flash twice and then
dim. After two minutes, the battery will be completely
discharged and the drill will immediately shut down. At this
point, replace with a freshbattery.

WARNING: To reduce the risk of injury, always have a
back‑up battery or secondary lighting available if the
situation warrantsit.
Keyless Single Sleeve Chuck (Fig.G–I)

WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changingacces sories.

WARNING: Always ensure the bit is secure before
starting the tool. A loose bit may eject from tool
causing possible personalinjury.
Your tool features a keyless chuck
6
with one rotating
sleeve for one-handed operation of the chuck. To insert a
drill bit or other accessory, follow thesesteps.
1. Turn tool off and disconnect tool from powersource.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desiredaccessory.
3. Insert the accessory about 3/4" (19 mm) into the chuck
and tighten securely by rotating the chuck sleeve
clockwise with one hand while holding the tool with the
other. Your tool is equipped with an automatic spindle
lock mechanism. This allows you to open and close the
chuck with onehand.
Fig. H
Fig. I
Fig. G
6
Be sure to tighten chuck with one hand on the chuck sleeve
and one hand holding the tool for maximumtightness.
To release the accessory, repeat steps 1 and 2above.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury. Exception—Tool
Connect™ functions and mode adjustments require
battery to beinstalled.