DeWalt DCE592 - Operation; Installing and Removing the Battery Pack; Recommended Materials

ENGLISH
12

CAUTION: On very porous materials or materials with
fine fissures, the DCE592 will not work. This includes
some limestone, dry cast concrete, and most OSB board.
Typical Nonporous Materials
• Glass • Finished fiberglass
• Smooth tile • Plastic
• Marble • Metal
Do Not Use On These Materials

WARNING: DO NOT use the DCE592 for any
unintendedpurposes.

WARNING: DO NOT lift materials that are not
supposed to be lifted.
• Slate • Plastic sheeting
• Glass that is less than
1/8"(3 mm) thick
• Rubber or other
flexiblematerials.

WARNING: Do not use on materials like slate, which is
a foliated rock. A seal may be created on the top surface,
but the layers can separate causing the rest of the
material to come away and the vacuum seal to break.

CAUTION: When lifting laminated materials like
counter tops the seal may be created on the top surface,
but the layers can separate causing the rest of the
material to come away and the vacuum seal to break.

CAUTION: Always remove any protective films from
the load area where the DCE592 will be attached.

CAUTION: DO NOT use on very thin or brittle surfaces
including glass under 1/8" (3 mm) thick. The vacuum
pressure can cause the material to flex and break.

CAUTION: DO NOT use on thin plastic sheets, rubber
or other flexible materials. The vacuum pressure can pull
the material up against the vacuum release valve in the
vacuum lifter. This will prevent the release of the material.
1. As the vacuum pressure begins to drop, over time, the
vacuum pump will automatically activate until the full
vacuum pressure is obtained again.
2. Do not disable the vacuum button
8
until you are ready
to release the load.
Recommended Materials

WARNING: Always test lift item a few inches to
ensure you know the capabilities of the DCE592 on the
material that you are lifting.

WARNING: Always attach the DCE592 as close as
possible to the center of gravity of the load. Ensure the
load is balanced during this test lift.

WARNING: Regardless of material being lifted, keep
the vacuum pump in the activated position until it is
time to safely release the load.
Typical Porous Materials
• Stone • Drywall
• Timber • Concrete
• Plywood • Cement board

CAUTION: When lifting semiporous materials such as
porous stone, timber, plasterboard, some OSB board or
concrete, ensure the vacuum pump remains in the on
position while lifting.

WARNING: When lifting porous loads the vacuum
pump may cycle on and off more frequently. Use
extreme caution if the vacuum pump cycles on and off
frequently or runs continually as it may not be able to
reliably lift the load. Lifting capability will be lower.
When being used to hand lift material the proper handposition
requires one hand on the mainhandle 
1
with your thumb
pointing toward the LED screen
6
.
Proper Hand Position (Fig. K)

WARNING: To reduce the risk of serious personal
injury, ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Installing and Removing the Battery Pack
(Fig. J)

WARNING: Ensure the tool/appliance is in the off
position before inserting the batterypack.
NOTE: For best results, make sure your battery pack is
fullycharged.
1. To install the battery pack
15
into the tool handle, align
the battery pack with the rails inside the tool’s handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does notdisengage.
2. To remove the battery pack from the tool, press the
battery pack release button
16
and firmly pull the
battery pack out of the toolhandle.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Lifting Materials (Fig. A, K–N)

WARNING: A single DCE592 offers up to 265lbs(120kg)
of horizontal lifting force and 132 lbs (60 kg)invertical
lifting force under ideal conditions. Refer to the
Intended Use section at beginning of this manual.

WARNING: Using the DCE592 while the battery charge
is below 20% may result in serious personal injury and
damage to the materials being lifted.

WARNING: Clean intended lifting material of any dust
and debris before attempting to lift.

WARNING: When lifting any item ensure the vacuum
button
8
remains activated while lifting. DO NOT slide
the on/off power switch
2
to the OFF position
21
.

WARNING: Inspect foam rubber seal for damage and
air filters for obstructions before each lift. If the vacuum
pressure falls faster than expected after the motor
stops, the foam rubber seal must be replaced.