DeWalt DCR027 - Assembly and Adjustments; Inserting and Removing Battery Pack; Fuel Gauge Battery Packs; Coin Cell Battery Installation

8
ENGLISH
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
withoutsupervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
ASSEMBLY AND ADJUSTMENTS

WARNING: Use only
DeWALT
battery packs andchargers.
Inserting and Removing the Battery Pack
from the Charger/Radio (Fig. B)
NOTE: Make sure your battery pack
19
is fullycharged.
To Install the Battery Pack into the Unit
1. Align the battery pack
19
with the rails inside the charger/
radio's battery port (Fig.B).
2. Slide it in until the battery pack is firmly seated and ensure
that you hear the lock snap intoplace.
To Remove the Battery Pack from the Unit
1. Press the release button
20
and firmly pull the battery pack
out of the toolhandle.
2. Insert battery pack into the charger as described in the
charger section of thismanual.
Fuel Gauge Battery Packs (Fig. B)
Some
DeWALT
battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the batterypack.
To actuate the fuel gauge, press and hold the fuel gauge
button
21
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to berecharged.
NOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-userapplication.
To Install Coin Cell Battery (Fig. B)

WARNING: Danger of explosion if battery is incorrectly
replaced. When replacing battery, replace it with the
same or equivalent type CR2032. Observe correct polarity
(+ and –) when replacing batteries. Do not store or carry
batteries so that metal objects can contact exposed
batteryterminals.
1. On the battery door on the back of the unit, turn the
screw 
22
anti-clockwise to remove. Screw will remain
captive in thedoor.
2. Press down on the battery door latch and pull toopen.
3. Install the coin cell battery
23
according to the diagram
inside the coin cell batteryarea.
4. Replace the battery door, insert the screw andtighten.
NOTE: To reset the LCD display, clock, and pre-sets remove
the coin cell battery and re-install. Follow this procedure if the
screen seems to lock inplace.

DANGER: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2hours and can lead
todeath.
Keep new and used batteries away from children. If the
battery compartment does not close securely stop using
the product and keep it away fromchildren.
If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medicalattention.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicableregulations.
Your Bluetooth® charger/radio is equipped with memory
capacity in order to store the time and your selected memory
channels. When the radio is in the OFF position, this memory
capacity is powered by one coin cell battery that is included
with the charger/radio.
Power/Volume Adjustment
1. To turn the radio on, press the power button
1
.
NOTE: When the radio is first used it will enter 'DAB' mode
and automatically scan for stations. It will then set the time
and start playing the first station it finds. If there is no time
signal available please refer to To Program the Clock to
manually set thetime.
2. Turn the dial
2
clockwise to increase the volume. To
decrease the volume, turn anti-clockwise.
Mode Function
To choose one of the mode functions('DAB', 'FM', or 'AUX' or
Bluetooth®) push the mode button
6
until the desired function
isfound.
NOTE: Pressing the Bluetooth® button
13
also puts the radio
into Bluetooth®mode.
DAB Mode
Tuning
When the unit is first switched on the unit will start in
'DAB'/'DAB+' mode and will 'Auto Scan' to find broadcast
stations in the local area. Once 'Auto Scan' is complete, use the
left or right arrow buttons
5
to scroll through thestations.
NOTE: When moving locations or if reception was poor
in the original scan(possible if the antenna was not up),
this may result in an empty or incomplete list of available
stations. Manually running an 'Auto Scan' will find all available
broadcaststations.
To Perform an Auto Scan:
1. Press the menu button
10
, scroll through the options by
pressing the right arrow button
5
until you reach 'Auto