DeWalt DCS369 Instruction Manual

11
ENGLISH
Register Online
Thank you for your purchase. Register your product nowfor:
• WARRANTY SERVICE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with yourproduct.
• CONFIRMATION OF OWNERSHIP: In case of an
insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
ofpurchase.
• FOR YOUR SAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
SafetyAct.
• Register online at www.dewalt.com
Repairs
The charger and battery pack are notserviceable. There are
no serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a
DeWALT
factory
service center or a
DeWALT
authorized service center.
Always use identical replacementparts.
Accessories

WARNING: Since accessories, other than those
offered by
DeWALT
, have not been tested with this
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only
DeWALT
recommended accessories should be used with
thisproduct.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact
DeWALT
call 1-800-4-
DeWALT
(1-800-433-9258) or visit our website: www.dewalt.com.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performingthisprocedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into aliquid.
Project Tips
• Cut only with sharp blades; they cut cleaner, faster and put
less strain on the motor whilecutting.
• When cutting, always ensure that the pivoting shoe
is resting against the workpiece. This will improve
operator control and minimizevibration.
• For longer blade life, use bi-metal blades. These
utilize a carbon steel back welded to high speed steel
teeth making the blade more flexible and less prone
tobreaking.
Fig.K
1
2
Pocket Cutting - Wood Only (Fig. K)
Measure the surface area to be cut and mark clearly with a
pencil, chalk orscriber.
1. Insert blade in blade clamp and tighten blade
clampsecurely.
2. Tip the saw backward until the back edge of the
pivoting shoe is firmly on the worksurface.
3. Switch motor on, permitting blade to attain
maximumspeed.
4. Grip handle steadily and begin a slow, deliberate
upward swing with the handle of thesaw.
5. The blade will begin to feed into material. Always
be sure blade is completely through material before
continuing with pocketcut.
NOTE: In areas where blade visibility is limited, use the
edge of the pivoting shoe as aguide.
Fig.J
NOTE: You should spread a thin film of oil or other coolant
along the line ahead of the saw cut for easier operation
and longer blade life. For cutting aluminum, kerosene
ispreferred.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can causeinjury.

DeWalt DCS369 Specifications

General

Amperage	- A
Power source	Battery
Sound power level	95 dB
Sound pressure level	84 dB
Cutting depth in wood	90 mm
Cutting depth in steel	40 mm
Idle stroke rate (max)	2800 spm
Vibration level (board)	8.1 m/s²
Vibration level (wooden beam)	5.5 m/s²
Motor type	Brushless
Product color	Black, Yellow
Built-in light	Yes
Orbital action	-

Weight and Dimensions

Weight	1430 g