DeWalt DW718V - Page 28

26
ENGLISH
MITRE SAW DW718/DW718V/DW718XPS
Congratulations!
You have chosen a DEWALT tool. Years of experience, thorough product
development and innovation make DEWALT one of the most reliable
partners for professional power tool users.
Technical Data
DW718/DW718V/
DW718XPS
Voltage V 230
(U.K. & Ireland only) V 230/115
Power input W 1,600
Blade diameter mm 305
Blade bore mm 30
Blade body thickness mm 1.8
Max. blade speed min
-1
1,700–3,400
Max. cross-cut capacity 90° mm 345
Max. mitre capacity 45° mm 241
Max. depth of cut 90° mm 90
Max. depth of bevel cross-cut 45° mm 56
Mitre (max. positions) left 60°
right 50°
Bevel (max. positions) left 48°
right 48°
0° mitre
Resulting width at max. height 94 mm mm 328
Resulting height at max. width 345 mm mm 74
45° mitre left
Resulting width at max. height 94 mm mm 231
Resulting height at max. width 241 mm mm 74
45° mitre right
Resulting width at max. height 94 mm mm 231
Resulting height at max. width 241 mm mm 74
45° bevel left
Resulting width at max. height 61 mm mm 328
Resulting height at max. width 345 mm mm 48
45° bevel right
Resulting width at max. height 43 mm mm 328
Resulting height at max. width 345 mm mm 28
31.62° mitre, 33.85° bevel
Resulting height at max. width 168 mm mm 23
Automatic blade brake time s < 10.0
Weight kg 20.5*
* DW718V with laser, DW718XPS with worklight LED
L
pA
(sound pressure) dB(A) 88
L
WA
(acoustic power) dB(A) 101
K
pA
(sound pressure uncertainty) dB(A)
2.8
K
WA
(acoustic power uncertainty) dB(A) 2.8
Vibration total values (triax vector sum) determined according to EN 61029:
Vibration emission value a
h
a
h
= m/s² < 2.5
Uncertainty K = m/s² 1.5
Fuses:
Europe 230 V tools 10 Amperes, mains
U.K. & Ireland 230 V tools 13 Amperes, in plugs
U.K. & Ireland 115 V tools 16 Amperes, mains
Defi nitions: Safety Guidelines
The definitions below describe the level of severity for each signal word.
Please read the manual and pay attention to these symbols.
DANGER: Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
EC-Declaration of conformity
DW718/DW718V/DW718XPS
DEWALT declares that these products, described under “technical data” have
been designed in compliance with:
98/37/EC (until Dec.28,2009); 2006/42/EC (from Dec.29,2009);
2004/108/EC; 2006/95/EC; EN 61029-1:2000 + A11:2003 + A12:2003;
EN 61029-2-9:2002; EN 55014-1; EN 55014-2; EN 61000-3-2;
EN 61000-3-3.
For more information, please contact DEWALT at the following address or
refer to the back of the manual.
The undersigned is responsible for compilation of the technical file and
makes this declaration on behalf of DEWALT.
Horst Grossmann
Vice President Engineering and Product Development
DEWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
Safety Instructions
WARNING! When using electric tools basic safety precautions
should always be followed to reduce the risk of fire, electric
shock and personal injury including the following.
Read all these instructions before attempting to operate this product and
save these instructions.
SAVE THIS MANUAL FOR FUTURE REFERENCE
General Safety Rules
1. Keep work area clear.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250 - 300 Lux). Do not use
the tool where there is a risk of causing fire or explosion, e.g., in the
presence of flammable liquids and gases.
3. Guard against electric shock.
Avoid body contact with earthed surfaces (e.g., pipes, radiators,
cookers and refrigerators). When using the tool under extreme
conditions (e.g., high humidity, when metal swarf is being produced,
etc.), electric safety can be improved by inserting an isolating
transformer or a (FI) earth-leakage circuit-breaker.