8. 위쪽의 알렌 핀이 바닥면과 같은 높이가 될
구멍을 살짝 넣어주십시오. 핀을 놓으면 잠금
상태가 됩니다(그림 8, 9).
9. 자동대패 뒷부분에 테이블을 부착하려면,
테이블과 자동대패를 함께 옮기려면, 설명서에 따라 접어서 옮기십시오.
위치에서는 아래쪽 나사에 있어야 합니다.
게 다칠 수 있습니다.
1. 바닥면에 있는 스프링이 끼워져 있는 볼트를 누르고 테이블의 양 끝을 살짝 사용자
쪽으로 움직이면 구멍이 분리됩니다. 쉽게 테이블을 떼도록 바닥면과 평평한 볼트
를 누르기 위해 T형 렌치를 사용할 수도 있습니다.
2. 테이블을 재부착할 필요가 있을 때까지 바닥면에서 부품들(계단형 볼트,
작은 알렌 캡 나사)를 떼어놓으십시오.
11
base. Use the T-wrench to tighten that
fastener securely (Fig. 8).
8. Depress the top Allen pin until it is flush
with the base and slide the top hole of
the table over the pin and release the pin
so they lock together (Fig. 8, 9).
9. To attach the table to the rear of the
planer, install the bolts and spring follow-
ing the above procedure. Your tables
should now fold up and down on the
top Allen screw and rest on the bottom
screw while in position for planing.
NOTE: To transport the planer with the tables, fold them up and carry the unit as
recommended by the planer manual.
WARNING: For your own safety, it is recommended that two people carry this
machine or serious injury could result.
TO REMOVE THE TABLES
1. Depress the spring-loaded bolts on the base and slide each end of the table
toward you so they disengage the holes in the tables. You may want to use the
T-wrench from your planer to push the bolts flush with the base to easily remove
the tables.
2. Leave the hardware (stepped bolts and small Allen cap screw) in the base
until you need to re-attach the tables.
REPAIRS
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
should be performed by authorized service centers or other qualified service person-
nel. Always use identical replacement parts.
GUARANTEE
Applicable to hand help power tools, lasers and Nailers.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship
for three years from the date of purchase. Please return the complete unit, transporta-
tion prepaid, to any DEWALT Service Centre, or any authorised service station.
For warranty repair information, call 1800 654 155.
This warranty does not apply to
• Accessories
• Damage caused where repairs have been made or attempted
by others.
• Damage due to misuse, neglect, wear and tear, alteration or
modification.
This warranty gives you specific legal rights and you may have other rights under the
provisions of the Consumer Guarantee Act 1993 (New Zealand only), Trade Practices
Act 1974 and State Legislation (Australia only).
In addition to the warranty, DEWALT tools are covered by our:
Free One Year Service Contract
DEWALT will also maintain the tool for free at any time during the first year of purchase.
This includes labour, parts and lubrication required to restore the product to sound
mechanical and/or electrical condition. Normal wear parts are not covered in this
service. Carbon brushes worn more then 50% will be replaced.
NOTE: 3 Year warranty is not applicable to items deemed as consumables. Radial
arm saws are covered by a one (1) year warranty only. DEWALT Reserves the right to
review its warranty policy prior to launch of any new business development products.
30 Day No Satisfaction Guarantee
If you are dissatisfied with any DEWALT power tool, laser or nailer, for any reason,
simply return it to the point of purchase with your sales receipt within 30 days for a
replacement unit or a full refund.
FIG. 7
FIG. 8
FIG. 9
관리, 조정 등을 받아야 합니다. 항상 동일한 교체품을 사용하십시오.
To Next Page
Loading...
