DeWalt DW777 - Residual Risks; Package Contents

eNgliSh
23
 • Considerapplyingspeciallydesignednoise-reductionblades.
 • DonotuseHSSblades.
 • Donotusecrackedordamagedsawblades.
 • Donotuseanyabrasivediscs.
 • Neveruseyoursawwithoutthekerfplate.
 • Raisethebladefromthekerfintheworkpiecepriortoreleasingthe
switch.
 • Donotwedgeanythingagainstthefantoholdthemotorshaft.
 • Thebladeguardonyoursawwillautomaticallyraisewhenthearm
is brought down; it will lower over the blade when guard lock up
release lever (b) is pushed.
 • Neverraisethebladeguardmanuallyunlessthesawisswitched
off. The guard can be raised by hand when installing or removing
saw blades or for inspection of the saw.
 • Checkperiodicallythatthemotorairslotsarecleanandfreeof
chips.
 • Replacethekerfplatewhenworn.
 • Disconnectthemachinefromthemainsbeforecarryingoutany
maintenance work or when changing the blade.
 • Neverperformanycleaningormaintenanceworkwhenthe
machine is still running and the head is not in the rest position.
 • Whenpossible,alwaysmountthemachinetoabench.
 • Connectthesawtoadustcollectiondevicewhensawingwood.
Always consider factors which influence exposure of dust such as:
-– Type of material to be machined (chip board produces more
dust than wood);
-– Correct adjustment of the saw blade;
-– Ensure that the local extraction as well as hoods, baffles and
chutes are properly adjusted.
 • Operatorshallbeinstructedonfactorsinfluencingexposureto
noise (e.g., use of saw blade designed to reduce the emitted noise,
saw blade and machine maintenance);
-– Report faults in the machine, including guards or saw blade, as
soon as they are discovered;
  -–Provideadequategeneralorlocalizedlighting;
-– Ensure the operator is adequately trained in the use, adjustment
and operation of the machine;
-– When fitted with laser, no exchange with different type of
laser permitted. Repairs shall only be carried out by the laser
manufacturer or an authorized agent.
Residual risks
The following risks are inherent to the use of saws:
– injuries caused by touching the rotating parts
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be
avoided. These are:
– Impairment of hearing.
– Risk of accidents caused by the uncovered parts of the rotating
saw blade.
– Risk of injury when changing the blade.
– Risk of squeezing fingers when opening the guards.
– Health hazards caused by breathing dust developed when sawing
wood,especiallyoak,beechandMDF.
Package contents
The package contains:
1 Partly assembled machine
2 Allen key 4/6 mm
1 216 mm TCT saw blade
2 Dust extraction nozzles
1 Dust bag
1 Instruction manual
1 Exploded drawing
 • Checkfordamagetothetool,partsoraccessorieswhichmay
have occurred during transport.
 • Takethetimetothoroughlyreadandunderstandthismanualprior
to operation.
Description (fig. 1, 2, 9)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
INTENDED USE
Your cross-cut mitre saw has been designed for professional cutting of
wood, wood products and plastics. It will perform the sawing operations
of cross-cutting, bevelling and mitring easily, accurately and safely.
DO NOT use under wet conditions or in presence of flammable liquids
or gases.
This cross-cut mitre saw is a professional power tool. DO NOT let
children come into contact with the tool. Supervision is required when
inexperienced operators use this tool.
a. On/off switch
b. Guard lock up release lever
c. Carrying handle
d. Fixed upper guard
e. Outer flange
f. Blade bolt
g. Lower blade guard
h. Saw blade
i. Sliding fence lock knob
j. Fixed table
k. kerf plate
l. Mitre arm
m. Mitre latch
n. Rotating table/mitre arm
o. Mitre scale
p. Sliding fence
q. Dust extraction nozzle
r. Traverse lock
s. Guard lock up hook
t. Bevel clamp handle
u. Bevel scale
v. Bench mounting holes
w. Lock down button
x. Traverse bars
y. Saw head
z. Allen keys
aa. Cable clamp
bb. Cable
cc. Speed control dial
dd. Padlock hole
ee. Override button
ff. Carrying handle (left and right)
gg. Inner flange
OPTIONAL ACCESSORITES (FIG. 3–6)
hh. Table end plate
ii. Support guide rails
jj. Material support plate
kk. Material clamp
ll. Swivelling stop
mm. Adjustable stand 760 mm (max. height)
nn. Legstand
oo. Length stop for short workpieces (to be used with guide rails [ii])
pp. Roller table