EasyManuals Logo

DeWalt dwe6411 Manual

DeWalt dwe6411
24 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #9 background imageLoading...
Page #9 background image
ENGLISH
7
3. Reattach the dust bag back onto the outlet and
lock into place by turning the dust bag collar
clockwise.
You may notice that all the dust will not come
free from the bag. This will not affect sanding
performance but will reduce the sander’s dust
collection efficiency. To restore your sander’s dust
collection efficiency, depress the spring inside the
dust bag when you are emptying it and tap it on the
side of the trash can or dust receptacle.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
WARNING: .
• Makesureallmaterialstobesanded
are well secured.
• Applyonlyagentlepressuretothe
workpiece. Excessive pressure does
not improve the sanding effect, but
only results in an increased load on
the machine and causes the abrasive
to tear.
• Avoidoverloading.
WARNING: Do not sand magnesium!
Proper Hand Position (Fig. 9A, 9B)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the main
handle or on the top of the unit as shown in Figures
9A and 9B.
Switching On and Off (Fig. 1)
To switch the tool on, set the on/off switch (A) to
position I.
To switch the tool off, set the on/off switch to
position O.
Sanding
1. Start with the coarsest grit size.
2. As the tool produces small scratch marks in all
directions, it is not necessary to sand with the
grain.
3. Check your work at short intervals.
4. Always switch off the tool when work is finished
and before unplugging.
MAINTENANCE
Your D
e
WALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.

Other manuals for DeWalt dwe6411

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the DeWalt dwe6411 and is the answer not in the manual?

DeWalt dwe6411 Specifications

General IconGeneral
Sound power level93 dB
Sound pressure level82 dB
Sound level uncertainty3 dB
Oscillating orbit diameter1.6 mm
Idle oscillation rate (max)14000 OPM
Power230 W
Uncertainty K1.5 m/s²
Maximum paper size140 x 115 mm
Vibration emission4 m/s²
Product colorBlack, Yellow
Type of sanderOrbital sander
Power sourceAC
Weight and Dimensions IconWeight and Dimensions
Depth160 mm
Height135 mm
Weight1280 g
Sanding plate size (WxD)108 x 115 mm

Related product manuals