14
ENGLISH
efficiency. To restore your saw's dust collection efficiency, depress the spring
inside the dust bag when you are emptying it and tap it on the side of the
trash can or dustreceptacle.
External Dust Extraction
When vacuuming dry dust that is especially detrimental to health or
carcinogenic, use a special dust Class M vacuumcleaner.
Connecting to an AirLock Compatable Dust Extractor (Fig.U)
The dust port
31
on your mitre saw is compatable with the D
WALT
AirLock connection system. The AirLock allows for a fast, secure connection
between the dust extractor hose and the mitresaw.
1. Ensure the collar on the AirLock connector
45
is in the unlock position.
Align notches on collar and AirLock connector as shown for unlock and
lockpositions.
2. Push the AirLock connector onto the dust port
31
.
3. Rotate the collar to the lockedposition.
NOTE: The ball bearings inside collar lock into slot and secure
the connection.The mitre saw is now securely connected to the
dustextractor.
MAINTENANCE
Your
power tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regularcleaning.
WARNING: To reduce the risk of serious personal injury, turn
tool off and disconnect tool from power source before making
any adjustments or removing/installing attachments or
accessories. Be sure the trigger switch is in the OFF position. An
accidental start-up can causeinjury.
WARNING: If the saw blade is worn, replace it with a new sharpblade.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
Before use, carefully check the upper blade guard, movable lower blade
guard as well as the dust extraction tube to determine that it will operate
properly. Ensure that chips, dust or workpiece particle cannot lead to
blockage of one of thefunctions.
In case of workpiece fragments jammed between saw blade and guards
disconnect the machine from the power supply and follow the instructions
given in section Changing or Installing a New Saw Blade. Remove the
jammed parts and reassembling the sawblade.
WARNING: Blow dirt and dust out of the main housing with dry air
as often as dirt is seen collecting in and around the air vents. Wear
approved eye protection and approved dust mask when performing
thisprocedure.
WARNING: Never use solvents or other harsh chemicals for cleaning
the non-metallic parts of the tool. These chemicals may weaken the
materials used in these parts. Use a cloth dampened only with water
and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into aliquid.
WARNING: To reduce the risk of injury, regularly clean the
tabletop.
WARNING: To reduce the risk of injury, regularly clean the dust
collectionsystem.
Optional Accessories
WARNING: Since accessories, other than those offered by
,
have not been tested with this product, use of such accessories with
this tool could be hazardous. To reduce the risk of injury, only
recommended accessories should be used with thisproduct.
Range of saw blades available (recommended blades)
Type of blade Blade dimensions
(diameter x bore x no. of teeth)
Usage
DT4310 series 40 216x30x24 For general purpose, ripping and cross-
cutting of wood and plastics
DT4286 series 40 216x30x80 TCG for use with aluminum
DT4320 series 60 216x30x48 ATB for fine cutting of manmade and
natural wood
DT4350 series 60 216x30x60 TCG for extra fine cutting of manmade
and natural wood
Consult your dealer for further information on the appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked with this
symbol must not be disposed of with normal householdwaste.
Products and batteries contain materials that can be recovered or
recycled reducing the demand for raw materials. Please recycle
electrical products and batteries according to local provisions. Further
information is available at www.2helpU.com.
To Next Page
Loading...
Need help?
General
