DeWalt XR Li-Ion TOOL CONNECT DCD992 - Coin Cell Battery

38
ENGLISH
Your tool features a keyless chuck
6
with one rotating sleeve for
one-handed operation of the chuck. To insert a drill bit or other
accessory, follow thesesteps.
1. Turn tool off and disconnect tool from powersource.
2. Grasp the black sleeve of the chuck
6
with one hand and
use the other hand to secure the tool. Rotate the sleeve
anticlockwise (as viewed from the front) far enough to
accept the desiredaccessory.
3. Insert the accessory about 19 mm into the chuck and
tighten securely by rotating the chuck sleeve clockwise
with one hand while holding the tool with the other hand.
Continue to rotate the chuck sleeve until several ratchet
clicks are heard to ensure full grippingpower.
NOTE: Be sure to tighten chuck with one hand on
the chuck sleeve and one hand holding the tool for
maximumtightness.
To release the accessory, repeat steps 1 and 2above.
Mode Selector (Fig. A, D)
Your tool is equipped with a mode selector that allows 3 modes
17
to be customized using the Tool Connect™ app. Home
settings are active when the home indicator
16
is lit. Refer to
Table 1 for customizablefeatures.
Once configured, pressing the mode button
14
on the foot of
the tool will cycle through the modes
17
.
If you are unsure of the current configuration, press the mode
selector button
14
to set the tool to the Home setting (home
indicator
16
is lit).
DeWALT
Tool Connect™

WARNING: To reduce the risk of injury, remove accessories
from the tool chuck before any Tool Connect™interaction.
NOTICE: Always check the tool configuration prior to use.
If you are unsure of the current configuration, press the
mode selector button
14
(Fig. D) to set the tool to the
Home setting as described on the label and thismanual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://www.
bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx)
DeWALT
Tool Connect™ is an application for your smart device
(such as a smart phone or tablet) that connects the device to
your tool to allow you to configure specific tool functions. Refer
to ModeSelector.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by
DeWALT
is under license. Other trademarks and
trade names are those of their respectiveowners.
NOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobileapplication.
Download the
DeWALT
Tool Connect™ applicationat:
• Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from theTool.
• Follow the instructions in the app to create your Tool
Connect™account.
• On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to theapp.
• To connect your tool with the
DeWALT
Tool Connect™ app,
at the appropriate screen, press the mode selector button
14
for 3–5 seconds, then wait for the tool to connect. The
tool can only be connected to one Tool Connect™ account
at atime.
Once the tool has been connected, you can confirm that you
would like to register the product.
DeWALT
.comaccount.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
DeWALT
service center. Do not attempt to replace the coin cell
batteryyourself.

WARNING: Danger of explosion if battery is
incorrectlyreplaced.

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2hours and can lead
todeath.
• Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away fromchildren.
TABLE 1
Customizable Features Home
Factory Presets
Customizable
RangeMode 1 Mode 2 Mode 3
Worklight brightness MED OFF MED HIGH OFF-HIGH
Worklight delay off 20 secs 20 secs 20 secs 20 minutes 0–20 minutes
Maximum speed (RPM)
in Drill Mode
Speed 1
Speed 2
Speed 3
450
1300
2000
450
1300
2000
450
1300
2000
450
1300
2000
140–450
400–1300
600–2000
Bind-Up Control®
Disabled Disabled Disabled Disabled
Disabled/
Enabled