Digi Z4500 Series - User Manual

To Next Page

Digi Monitoring & Control Products

Hardware Guide

Main Page

Trademarks and Copyright2
Warranty2
Technical Support2
Table of Contents4
Digi Monitoring & Control Products Hardware Guide7
Applicable Hardware7
Assemble the Hardware8
Assemble the Connect Sensor+ Hardware9
Before You Begin: Activate the SIM Card in Your Devices9
Step 1: Open the Box and Remove Components Needed for Assembly10
Step 2: Assemble the Connect Sensor10
Step 3: Check the Cellular Connection11
Step 4: Wire the Input Sensors12
Step 5: Register the Device13
Assemble the Connect Sensor XRT-M NEMA Hardware14
Step 1: Open the Box and Remove Components Needed for Assembly14
Step 2: Install the Batteries in the Connect Sensor XRT-M NEMA15
Step 3: Check the Cellular Connection16
Step 4: Register the Device18
Step 5: Verify Connect Sensor XRT-M NEMA Registration20
Step 6: Wire the Input Sensors22
Step 7: Configure the Connect Sensor XRT-M NEMA23
Assemble the Z45 Controller Hardware24
Before You Begin: Activate the SIM Card in Your Devices24
Step 1: Open the Box and Remove Components Needed for Assembly24
Step 2: Wire a Power Supply to the Z45 Controller and Power the Device26
Step 3: Optional: Insert a Second SIM Card into the Z45 Controller27
Step 4: Attach the Antennas to the Z45 Controller28
Step 5: Power the Z45 Controller28
Assemble the RMS Z4550 Hardware29
Before You Begin: Activate the SIM Card in Your Devices29
Step 1: Open the RMS Z45 Enclosure and Verify the Components29
Step 2: Optional: Insert a Second SIM Card into the RMS Z4530
Step 3: Attach Antenna Cables to the RMS Z4531
Step 4: Attach an Accessory to the RMS Z4531
Step 5: Power the RMS Z4532
Step 6: Close and Lock the RMS Z45 Enclosure33
Connect Sensor+ Hardware Reference34
List of Connect Sensor+ Digi Axess Components and Accessories34
Included in the Box34
Optional Accessories35
Connect Sensor+ Ports and Buttons35
Manually Wake the Connect Sensor37
Manually Wake the Device: Magnet Swipe37
Manually Wake the Device: Wake Button37
Connect Sensor+ LED Start-Up Sequence38
Closing the Connect Sensor38
Wiring the Connect Sensor+ I/O Interface39
Prerequisites39
Wire the Sensors to the Connect Sensor+ I/O Interface39
Connect Sensor+ I/O Interface Pin Assignments41
Analog Input43
Voltage Input43
Current Loop44
Digital I/O Pin46
Modbus Serial Power Output47
Analog Input Schematic48
Digital I/O Schematic49
Device Not Connected to the Cellular Network50
Verify SIM Configuration50
Check Cellular Antenna50
Verify Cellular Network Coverage50
Check Battery Life50
Manually Configure the Cellular Connection50
Battery Care and Maintenance52
Battery Life52
Battery Sleep and Wake Modes52
Battery Orientation52
Battery Percentage and External Power52
Battery Depletion53
Battery Inspection53
Battery Passivation53
Replace a Battery53
Reset the Connect Sensor54
Install the Magnet Mount on a Connect Sensor55
Safety Notices: Connect Sensor56
Assembly Safety Information56
Battery Safety56
Safety Notices57
Installation Considerations57
Technical Specifications: Connect Sensor59
Maximum Power and Frequency Bands59
Cell Modem Transmit (TX) Output Power59
Regulatory Information: Connect Sensor59
Fcccertifications and Regulatory Information59
Declaration of Conformity (Doc)60
Connect Sensor XRT-M NEMA Hardware Reference61
List of Connect Sensor XRT-M NEMA Components and Accessories61
Optional Accessories62
Connect Sensor XRT-M NEMA Device Description62
Interior Components62
Exterior Components64
Connect Sensor XRT-M NEMA LED Status Indicators65
LED Sequences66
Wire the Sensors to the Connect Sensor XRT-M NEMA I/O Interface66
Equipment Needed66
Connect Sensor XRT-M NEMA I/O Interface Pin Assignments68
Manually Wake the Connect Sensor XRT-M NEMA70
Connect Sensor XRT-M NEMA Battery Replacement, Care, and Safety70
Replace the Batteries in a Connect Sensor XRT-M NEMA71
Battery Safety72
Battery Life in a Connect Sensor XRT-M NEMA73
Wire a Power Source to the Connect Sensor XRT-M NEMA73
Power Source Requirements73
Close the Connect Sensor XRT-M NEMA Case76
(Optional) Install the Magnet Mount on a Connect Sensor XRT-MNEMA76
Safety Notices: Connect Sensor XRT-M NEMA77
Installation Considerations for the Connect Sensor XRT-M NEMA77
Warnings: Explosion Hazards78
RF Exposure Statement79
Ul/Cul Conformity for Connect Sensor XRT-M NEMA79
Technical Ratings: Connect Sensor XRT-M NEMA80
Electrical80
Environmental80
Z45 Controller Hardware Reference81
List of Z45 Controller Components and Accessories81
Included Equipment81
Required Additional Equipment81
Power the Z45 Controller Using a Barrel Connector Pigtail82
Tools Needed83
Reset a Z45 Controller to the Default Factory Settings84
Connect the Ethernet Cable to the Z45 Controller84
Z45 Controller Indication/Terminations/Switches84
Z45 Controller Digital Inputs87
Circuit Summary87
Using the Analog Inputs of the Z45 Controller89
Using the Digital Outputs of the Z45 Controller90
Regulatory Information: Z45 Controller91
Fcc91
RMS Kit Hardware Reference92
RMS Z4550 Kit Components92
Components92
Accessories Bag93
Mount the RMS Z45 to a Solid Surface93
Attach the RMS Z45 to the DIN Rail95
Connect the Power Supply to the RMS Z4596
Tools Needed96
Detach an Accessory from the RMS Z4598
Detach the Antenna Cables from the RMS Z4599
Disconnect the Power Supply from the RMS Z45100
Detach the RMS Z45 from the DIN Rail102

Need help?

Do you have a question about the Digi Z4500 Series and is the answer not in the manual?

Digi Z4500 Series Specifications

General

Brand	Digi
Model	Z4500 Series
Category	Network Hardware
Language	English

Related product manuals

Digi Z4500 Series - User Manual

Table of Contents

Digi Z4500 Series Specifications

Related product manuals