The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confidential. Any disclosure, copying, distribution to third
party is strictly prohibited.
Enable visualization MB2 with password? - If the visualization of memory-block number 2 has been inhibited (see Q.327) should it be possible to undo this with the
password? The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
Inhibit printing memory-block n. 2? - Should it be impossible to print memory-block number 2? See also Q.330.
The allowed answer is either: 0 (No: print) or: 1 (Yes: inhibit).
Enable printing MB2 with password ? - If the printing of memory-block number 2 has been inhibited (see Q.329) should it be possible to undo this with the password?
The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
Inhibit reset of memory-block n. 2 ? - Should it be impossible to reset memory-block number 2 from panel?
See also Q.332. The allowed answer is either: 0 (No: reset from panel) or: 1 (Yes: inhibit).
Enable reset of MB2 with password? - If the reset from panel of memory-block number 2 has been inhibited (see Q.331) should it be possible to undo this with the
password? The allowed answer is either: 0 (No: keep inhibited) or: 1 (Yes: enable with password).
Enable auto-advance of stat. memory? - Should the number of the statistics-memory advance automatically (instead of manually) during the reading-procedure ?
The allowed answer is either: 0 (No: manually) or: 1 (Yes: automatically).
Divide income of mem.-block n. 2 by 100? - Should the income of memory-block n. 2 be divided by 100 (or 1000) thus not showing the decimal point?
The allowed answer is either: 0 (No: don't divide) or: 1 (Yes: divide).
Hide on the Ticket the message "Thanks"?
Enable on the Ticket the 3 lines footer?
from Q 338 to Q 339 available for any possible software extension
FIXED COST FARE (forfait)
Enable appl. of cost with num. keypad? - Enable the application of a fixed cost with the numeric keypad?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
Enable programming forfait with front keys? - If yes then, with the taximeter in Hired and pressing the keys K1 + K4 together, the forfait amount can be programmed
on the primary display. On the secondary display the text FORFA will be shown.
Programming:
pressing key K1 increases the amount with 1 unit pressing key K2 increases the amount with 10 units;
pressing key K3 increases the amount with 100 units pressing key K4 increases the amount with 1000 units;
pressing keys K3 + K4 cancels the modifications made up to this point pressing key OP the forfait programming is exited.
Once exited from the forfait programming the amount shown on the display will not change anymore independently from the run distance or the waiting time until the next
time a new fare is started.
Note:
In order for this function to work well it is necessary to program several questions in block number 62 because this is the block that is loaded when the forfait is
used according to the following list:
Q13 = 0 : disable key K1
Q21 = 0 : no extra-charge n. 1
Q23 = 0 : no extra-charge n. 2
Q25 = 0 : no extra-charge n. 3
Q27 = 0 : no extra-charge n. 4
Q34 = Yes : disable distance measurement in Stopped
Q36 = Yes : disable distance measurement in Hired
Q37 = Yes : disable waiting-time measurement in Hired
Q40 = 0 : disable Night-time
Q41 = 0 : disable Night-time
Q52 = 0 : disable Holiday-time
Q53 = 0 : disable Holiday-time
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
Check Printer Status before start the trip - If Yes the taximeter checks the printer status before starting a new trip and if the printer is not connected or is not ready
then the trip will not start
Disable Print out shift report - If Yes the report will not be printed, if No the report will be printed at the end of the shift
from Q 348 / Available for custom parameters / to Q 367
CONNECTION TO THE DISPATCHER
Transmit undefined status to dispatcher? - Transmit an undefined status to the dispatcher? The allowed answer is either: 0 (No: don't transmit) or: 1 (Yes: transmit).
To Next Page
Loading...
Need help?
General
