
TheinformationcontainedherearepropertyofDIGITAXAutomotiveElectronicsItaly,andextremelyconfidential.Anydisclosure,copying,distributiontothird
partyisstrictlyprohibited.

30
Nr. Functions Value
13
Number of next block (absolute) with K1: determines the number of the next tariff-block to be used when key K1 is pressed in Hired Position. The allowed value goes from
0 (min) to 62 (max). 0 =Function disabled 1 to 62 = Block Number
0 - 62
14
Number of next block (absolute) with K2: determines the number of the next tariff-block to be used when key K2 is pressed in Hired Position. The allowed value goes from
0 (min) to 62 (max). 0 =Function disabled 1 to 62 = Block Number
0 - 62
15
Number of start-fare block (absolute) with OP: this is the number of the tariff-block to be used at the start of a fare when key OP is pressed (shortly) going from For-Hire to
Hired. See also Q.138. The allowed value goes from 0 (min) to 62 (max).
0 - 62
16
Number of start-fare block (absolute) with K2: this is the number of the tariff-block to be used at the start of a fare when key K2 is pressed going from For-Hire to Hired.
The allowed value goes from 0 (min) to 62 (max).
0 - 62
17
Number of end-fare block (absolute) with OP: this is the number of the tariff-block to be used at the end of a fare when key OP is pressed going from Hired to
Stopped.The allowed value goes from 0 (min) to 62 (max).
0 - 62
18
Time limit to Disable tariff change with K1: this is the maximum time during which it is allowed to manualy change the tariff by pressing key K1. The time is given in
seconds with an accuracy of 1 sec. The allowed value goes from 0 (min) to 9999 (max).
The value 0 is a special case. It means: no time limit; so, in that case key K1 is always enabled.
0 - 9999
19
Distance in Stopped for automatic pass in For-Hire: this is the distance to run in Stopped position that will cause an automatic pass from Stopped to For-Hire. The
distance is given in metres with an accuracy of 1 m. The allowed value goes from 0 (min) to 255 (max). The value 0 is a special case. It means: disabled.
0 - 255
20
Distance in Stopped for automatic return to Hired: this is the distance to run in Stopped position that will cause an automatic return from Stopped to Hired. The distance is
given in metres with an accuracy of 1 m. The allowed value goes from 0 (min) to 255 (max). The value 0 is a special case. It means: disabled.
0 - 255
EXTRACHARGEN.1
21 Cost of Extra-Charge n. 1 in Hired with K2: this is the cost of extra charge number 1 in Hired that can be applied with key K2. The cost is given in the local currency with an
accuracy of 1. The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fixed decimal point.
0 - 65535
22
Number (max) of insertions of Extra-Charges n. 1: this is the maximum number of times that extra-charge number 1 can be applied.
The allowed value goes from 0 (min) to 255 (max).
0 –255
EXTRA-CHARGE N. 2
23 Cost of Extra-Charge n. 2 in Hired with K3: this is the cost of extra charge number 2 in Hired that can be applied with key K3. The cost is given in the local currency with an
accuracy of 1. The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fixed decimal point.
0 - 65535
24 Number (max) of insertions of Extra-Charge n. 2: this is the maximum number of times that extra charge number 2 can be applied. The value goes from 0 (min) to 255
(max).
0 - 255
EXTRA-CHARGE N. 3
25 Percentage or Fixed-Cost of Extra-Charge n.3 in Stopped with K2: this is the percentage or Fixed-Cost of extra-charge number 3 in Stopped that can be applied with key
K2. In order to establish whether this value has to be interpreted as a percentage or as a cost consult Q.30. The cost is given in the local currency with an accuracy of 1. The
allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fixed decimal point.
The percentage is given with an accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 -65535
cost or
percentage
26
Number (max) of insertions of Extra-Charge n. 3: this is the maximum number of times that extra charge number 3 can be applied.
The allowed value goes from 0 (min) to 255 (max).
0 - 255
EXTRA-CHARGE N. 4
27 Percentage or Fixed-Cost of Extra-Charge n.4 in Stopped with K3: this is the percentage or Fixed-Cost of extra charge number 4 in Stopped that can be applied with key
K3. In order to establish whether this value has to be interpreted as a percentage or as a cost consult Q.31. The cost is given in the local currency with an accuracy of 1. The
allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fixed decimal point.
The percentage is given with an accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 -65535
cost or
percentage
28
Number (max) of insertions of Extra-Charge n. 4: this is the maximum number of times that extra charge number 4 can be applied. The allowed value goes from 0 (min)
to 255 (max).
0 -255
EXTRA-CHARGES (from 1 to 4)
29 Cost limit for sum of all Extra-Charges (1 to 4): this is the maximum allowed cost of the sum of all manual extra charges. (sum of extra charge 1 to extra charge 4). The
cost is given in the local currency with an accuracy of 1. The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fixed decimal point.
0 - 65535
30 Is extra charge n.3 a percentage or a cost? - Determines whether extra-charge number 3 (the value of Q.25) is to be interpreted as a percentage (Yes) or as a cost
(No). The allowed answer is either 0 (No:Fixed-cost) or 1 (Yes: percentage of the fare).
0=cost
1=percentage
31 Is extra charge n.4 a percentage or a cost? - Determines whether extra charge number 4 (the value of Q.27) is to be interpreted as a percentage (Yes) or as a cost
(No). The allowed answer is either 0 (No: Fixed-cost) or 1 (Yes: percentage of the fare).
0=cost
1= percentage
32 Remember last used block num.? (next fare) - Should the last block number that has been used be remembered in order to be used again for the next fare? No / Yes
33
Enable discard current fare in Stopped? - This option enables the possibility to discard the statistics of the current fare by pressing the keys K4 and OP, passing to
ForHire. The allowed answer is either: No(enabled) or Yes (disabled).
No / Yes
34 Enable/disable measurements? - Should the distance measurement be disabled while in Stopped? The allowed answer is either: No(enabled) or Yes (disabled). No / Yes
35 Enable/disable measurements? - Should the waiting-time measurement be enabled while in Stopped? The allowed answer is either: No(enabled) or Yes (disabled). No / Yes
36 Enable/disable measurements? - Should the distance measurement be disabled while in Hired? The allowed answer is either: No(enabled) or Yes (disabled). No / Yes
37 Enable/disable measurements? - Should the waiting-time measurement be disabled while in Hired? The allowed answer is either: No(enabled) or Yes (disabled). No / Yes
NIGHT TIME (Prog - Date N. 1)
38 Start of night-time - This is the moment (whole or half hour) in which night-time starts. The time is given in whole hours with an accuracy of 1 hour. The allowed value goes
from 0 (min) to 23 (max). It is also possible to specify half hours. In order to do this add 100 to the programmed value.
For example, to program the hour 22:30 use the value 122.
0 - 23
39 End of night-time - This is the moment (whole or half hour) in which night-time ends.
The time is given in whole hours with an accuracy of 1 hour. The allowed value goes from 0 (min) to 23 (max). It is also possible to specify half hours. In order to do this add
0 - 23
To Next Page
Loading...
Need help?
General
