Diivoo WT-05 User Manual

Diivoo
Bluetooth Dual Water Timer
TTT
WT-05
Need Help?
: support@diivoosmart.com
Diivoo
Thank You
If you have any questions, please feel free to contact us firstly.
We are always here for you.
Pe
e The best range for connection and control is within
49.2ft in the open area.
e The bluetooth water timer does not support Alexa &
Google voice or remote control.
e Do not use your timer when the air temperature is
below 40*(4.5°C), the timers should be removed from
the hose faucet and stored indoors to avoid potential
frozen damage.
e Filter can trap dirt particles, please clean filter regularly
and replace if worn.
e Please replace batteries when the low battery indicator
appears the display. When replacing the power unit,
please make sure that the water timer is dry.
e To prevent leakage, make sure that the water timer is
tightly attached to the faucet and hose, add rubber
washer and thread seal tape if necessary.
Note:
(1) The water flow is reduced by half when the two zones
are turned on at the same time.
(2)The water flow in two zones may be different if you turn
on one zone first and then turn on the other zone.
PAM MM UT OM TE Cee ree as
Hose Faucet Connection
LED Light
ON/OFF Button
Outlet
Fitting NH3/4
Bluetooth Range 49.2ft without interference
Working Water Pressure | 7.25-116 psi
Working Temperature 40.1°F -113°F (4.5°C-45°C)
Rain Delay Time 1 day and up to 7 days
Waterproof IPX5
1x Water Timer,
2 x Threaded connector,
1x 1/2" inlet adapter,
3 x Extra Rubber Washers,
1x Thread Seal Tape,
Included in the Box
Instruction
3. Initial Water Timer Setup
1 Insert Four AA Batteries
1. Open the battery cover.
2. Insert four AA (1.5V) alkaline batteries. Please do not
insert rechargeable batteries to avoid low voltage.
Note:
a.Do not mix alkaline, standard
(carbon-zinc), or rechargeable ¢
(nickel cadmium) batteries.
b.Used up or dead batteries
must be removed from the
timer and disposed of properly.
2 Install the Timer
Connect the timer to an outdoor hose faucet.
Your timer is now ready to be used with any product
that can be attached to a standard hose faucet.
Note:
Do not place the timer in an underground valve
box or anywhere your Bluetooth signal will be
obstructed.
3 Turn on Your Water 4 Add a Device
The water must remain on for the timer to work
properly.
Cm Cm eh
1 Download the Smart Life App
Tap "Add device" or "+" to add the smart device
in app. Select "Industry&Agriculture" > "Water
valve controller(BLE)".
Waiting for connecting to be 100%. Edit the
name of your water timer completed.
Scan the QR code and download the free Android or
Reset the device first.
10S
app,
then
install
the
APP.
If
you
have
already
=
|
Benen
©
|
installed
the
Smart
Life
APP,
go
to
step
2.
-—4
b
[hl
aE
=
an
@
App
Store
—
ae
ae
[=]
=
=a
2 _s Enter configuration Mode
Long press either of the "On/OFF button" for 6s until
the two green lights flash quickly at the same time to
keep the water timer in pairing mode.
Note:
Make sure Bluetooth on your phone is turned on sett
i
i
Battery
Life
etting
during paring.
Weather
Zone Jone zea Zone2
On/OFF
button
Custom
image
——+
Custom
image
Manual watering r x
Function Manual watering
Function
Work Time Work Time
Oh 10min Oh 10min
Schedule for Zone 1 — Schedule for Zone 2
3 Open the Smart Life App
Create an account or login with an existing account
to begin timer setup.

Diivoo WT-05 Specifications

General

Model	WT-05
Type	Digital Timer
Display	LCD
Mounting Type	Plug-in
Weight	150g
Operating Temperature	0°C to 40°C
Timing Range	1 minute to 24 hours
Dimensions	120mm x 72mm x 35mm
Maximum Load	15A, 1800W