Caution
• Do not install the product in dusty or humid places. This may cause fi re or an electric shock, or damage the product.
• Do not install the product on an unstable surface. It may fall and cause injury to the user or other people.
• Do not allow foreign objects to enter into the product. They may cause an electric shock, a short circuit, a fi re, or damage the
product. If something falls into the product, immediately unplug the power cord, and then call a service representative.
• Do not open the cover while printing. This may damage the product.
• Do not spill or spray liquids or chemicals onto the product.
• When cleaning the cover, do not use thinner, trichloroethane, benzene, ketone-based cleaners, or chemically treated cloths.
They could discolor or deteriorate the cover.
• At least once a year, unplug the power cord, and clean the prongs and the plug. If dust accumulates, it may cause a fi re.
• When printing continuously for long periods in a small room, be sure to ventilate the room properly.
• If you intend to use the product on a transportation vehicle (train, truck, ship, etc.), please talk to a representative in advance.
• When disposing of the product, accessories, packaging materials, or media (paper, ribbon), please abide by local waste
removal ordinances. For details, contact your local government offi ces.
• When unplugging the cord, always grip the plug. Do not pull on the cord as it may damage the cord and cause an electric
shock or fi re.
• When moving the product, be sure to unplug the power cord. Otherwise, the cord may be damaged, which may cause fi re or
an electric shock.
• For safety, when not using the product for an extended period of time, be sure to unplug the power cord. Otherwise, it may
cause an electric shock, fi re, or a malfunction.
• Parts with this warning get extremely hot. Do not touch these parts after printing. There is a danger of burns.
• Do not touch the gear mechanisms. There is a danger of injury if fi ngers get caught in spinning gears.
Caution for installation
• Before using the product, read “For Safe Operation” carefully and observe the instructions therein.
• Use care when moving the product. Never try to carry the product alone. Dropping it may cause injury or property damage.
• Do not use or store the product near a fi re, humid places, in direct sunlight, near an air conditioner or heater, or any other location with
unusually high or low temperature, strong humidity, or excessive dust.
• Do not place the product where chemical reactions occur, such as in a laboratory.
• Do not install the product where there is salinity or corrosive gas in the air.
• The product must be installed on a fi rm, level surface where there is ample ventilation.
• Do not put anything on top of the product.
• Do not use the product near a radio or television, and do not use the same wall outlet for the product and a radio or television.
Otherwise radio or television reception may be adversely affected.
• Do not use a power voltage or a frequency other than those specifi ed.
• Do not put anything on the power cord or step on it.
• Do not drag or carry the product by the power cord or the USB cable.
• Avoid plugging the power cord into an outlet with many other cables connected.
• Do not bundle the power cord.
• Always grip the plug housing, not the cord, to plug or unplug the power cord.
• Always unplug the power cord before connecting or disconnecting the USB cable.
• Avoid using a long USB cable or connecting it to any noise-producing device. If it is unavoidable, use a shielded cable or twisted pair
for each signal.
• Use a shielded USB cable compatible with the USB 2.0 specifi cations.
• Place the product near the outlet where the power cord can be unplugged easily to shut the power off.
• Use an AC outlet that accepts a three-pronged plug. Otherwise, there may be a danger of electric shock.
• Do not use the cord set supplied with the printer for other devices.
• Use the cord set supplied for the product.
• This product is not intended for use in the immediate/direct visual fi eld of the display work place. To avoid disturbing refl ections on the
display work place, this product shall not be placed in the immediate/direct fi eld of vision.
Specifi cations
Print method Thermal dye sublimation transfer Rated current 100 V 3.9 A 240 V 1.6 A
Dimensions 275 mm(W) × 366 mm(D) × 170 mm(H)
Operating
environment
Temperature 5°C to 35°C
in natural convection conditions
Weight Approx. 12 kg (printer unit only)
Rated voltage AC100 V – 240 V 50 Hz/60 Hz Humidity 35% to 80% with no condensation
To Next Page
Loading...
