EasyManua.ls Logo

Dolmar BC-CS - User Manual

Dolmar BC-CS
80 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WARNING: Before use, read this booklet and the instruction manual of the power unit. Failure to follow the warnings and instructions may
cause serious or fatal injury.
AVERTISSEMENT : Avant d’utiliser l’outil, lisez la présente brochure et le manuel d’instructions du groupe moteur. Le non-respect des mises
en garde et instructions peut entraîner des blessures graves, voire mortelles.
WARNUNG: Lesen Sie vor Verwendung des Aufsatzes diese Broschüre und die Betriebsanleitung des Antriebs. Bei Nichtbeachten dieser
Warnungen und Anweisungen kann es zu schweren oder gar tödlichen Verletzungen kommen.
AVVERTENZA: Leggere il presente opuscolo e le istruzioni del gruppo di alimentazione prima dell’uso. La mancata osservanza delle
avvertenze e delle istruzioni può condurre a infortuni gravi o letali.
WAARSCHUWING: Lees voor gebruik deze gebruiksaanwijzing en de gebruiksaanwijzing van uw multifunctionele aandrijfsysteem
aandachtig door. Het niet volgen van de waarschuwingen en instructies kan leiden tot ernstig of fataal letsel.
ADVERTENCIA: Antes del uso, lea este folleto y el manual de instrucciones del grupo motor. Si no se siguen las advertencias y las
instrucciones, se pueden provocar lesiones graves o fatales.
AVISO: Antes da utilização, leia este folheto e o manual de instruções da unidade de alimentação. O não cumprimento dos avisos e
instruções pode causar ferimentos graves ou fatais.
ADVARSEL: Læs dette hæfte og brugsanvisningen til drivenheden inden brug. Det kan medføre alvorlig eller dødelig tilskadekomst, hvis du
ikke overholder advarslerne og følger instruktionerne.
ΠΡΟΕΙΔΟΠΟΙΗΣΗ: Πριν από τη χρήση, παρακαλούμε διαβάστε αυτό το φυλλάδιο και το εγχειρίδιο οδηγιών της κινητήριας μονάδας. Η
παράλειψη εφαρμογής των προειδοποιήσεων και των οδηγιών μπορεί να προκαλέσει σοβαρό ή θανατηφόρο τραυματισμό.
UYARI: Kullanmaya başlamadan önce, bu kılavuzu ve güç başlığının kullanım kılavuzunu okuyun. Verilen uyarılara ve talimatlara
uyulmaması ciddi ve hatta ölümcül yaralanmalara yol açabilir.
BC-CS
BC-AC
Original Instruction Manual
Instructions d’emploi d’origine
Originalbetriebsanleitung
Manuale di istruzioni originale
Originele gebruiksaanwijzing
Instrucciones de manejo originales
Instruções de serviço original
Original brugsanvisning
Πρωτότυπο εγχειρίδιο οδηγιών
Orijinal Kullanım Kılavuzu

Table of Contents

Questions and Answers

  • J
    Joel JacksonAug 3, 2025
    Why is my Dolmar BC-CS Brush Cutter vibrating abnormally?
    • M
      Maria WrightAug 3, 2025
      If your Dolmar Brush Cutter vibrates abnormally, immediately stop the motor. This could be due to several reasons: * The cutting tool might be bent, worn, or broken, in which case you should replace it with a new one. * The cutting tool might not be tightened securely; ensure it is tightened properly. * If one end of the nylon cutting cord has broken, and the nylon cutting head is unbalanced, try feeding the nylon cutting cord by tapping the nylon cutting head on the ground. * The cutting blade might not be fitted correctly on the guide of the receive washer; install it properly. * If the drive system isn't working correctly, have an authorized Dolmar service center inspect and repair it.
  • N
    Nicholas ParkerAug 10, 2025
    What to do if the cutting tool on my Dolmar Brush Cutter does not rotate?
    • M
      Michael WrightAug 10, 2025
      If the cutting tool on your Dolmar Brush Cutter does not rotate, stop the motor immediately. This could be because the cutting tool isn't tightened securely, so make sure to tighten it. Alternatively, a twig might be caught between the cutting tool and the protector; remove any foreign matter. If neither of those solutions work, the drive system may not be functioning correctly, and you should ask a Dolmar authorized service center to inspect and repair it.
  • R
    Rebecca JacksonAug 17, 2025
    How to fix a Dolmar BC-CS when the nylon cutting cord does not feed?
    • P
      Philip HolmesAug 17, 2025
      If the nylon cutting cord on your Dolmar Brush Cutter does not feed, it might be that the cord is used up or tangled in the spool. Try rewinding the cord to resolve this issue.
  • H
    Heather WilliamsonAug 25, 2025
    Why is the nylon cutting cord not cut off at the correct length on my Dolmar BC-CS Brush Cutter?
    • L
      Laura ArnoldAug 25, 2025
      If the nylon cutting cord on your Dolmar Brush Cutter is not being cut off at the correct length, it could be due to the cord cutter on the protector being damaged or missing; in this case, ask Dolmar authorized service center to replace the cord cutter. Another possibility is that the cord extends past the protector, in which case you should rewind the cord.

Summary

Product Information and Safety

Approved Power Unit

Safety Precautions

Covers intended use, general safety, and personal protective equipment.

Work Area Safety

Guidelines for ensuring a safe operating environment.

Putting Into Operation

Starting Motor

Instructions for safely starting the power unit motor.

Operation and Maintenance

Operation Details

Cutting Tools

Information on different cutting tools and their safe use.

Kickback and Vibration

Explanation of kickback hazards and vibration effects.

Assembly and Adjustment

Attachment Procedures and Operation

Installing and Removing Components

Operational Adjustments

Maintenance and Storage Details

Inspection and Maintenance Procedures

Technical and Troubleshooting Information

Troubleshooting Guide

Lists common problems and their solutions.

Technical Data

Dolmar BC-CS Specifications

General IconGeneral
BrandDolmar
ModelBC-CS
CategoryBrush Cutter
LanguageEnglish

Related product manuals