Dolphin 3001 User Manual

3001
READ CAREFULLY BEFORE USING YOUR DOLPHIN ROBOTIC POOL CLEANER
DOLPHIN CADDY ASSEMBLY INSTRUCTIONS
Insert the wheel assembly (c-1 p.4) firmly into the groove underneath the yellow base ensuring it
is centered with a plastic washer (c-2 p.4) on each side.
Insert the 2 metal pipes (c-3 p.4) into the holes at the top of the white Caddy tower (c-4 p.4) until
they clip onto the wishbone clips in the studs at the base of the tower.
Fit the 2 hooks (c-5 p.4) to the top of the pipes until they clip into the wishbone clips.
Fit the top of the handle (c-6 p.4) in the upright position (see diagram) until it clips on the wishbone
clips in the hooks. Fig A.
INSTALLATION
The caddy and power supply (#1 p.5) should be positioned so that the DOLPHIN can reach all the
walls of the swimming pool. It must be in the shade and at a minimum distance of 10 ft (3 meters)
from the edge of the pool. Fig B.
Use only the original DOLPHIN power supply.
The power supply has been tested, and ETL approved (to UL1012 standard) for outdoor use.
Do not submerge power supply.
HANDLE
The DOLPHIN features an adjustable handle (#2 p.5) that is fitted into slots on each side of the
DOLPHIN body. This handle must be locked in a diagonal position across the top of the DOLPHIN
body in order to ensure optimum cleaning results.
Press downwards on each yellow latch (#3 p.5) to move each handle arm. Fig C.
To avoid cable coiling and for the most efficient cleaning pattern, reverse handle position after each
use. Fig D.
OPERATION
AVOID ENTERING THE SWIMMING POOL WHILE THE DOLPHIN IS IN OPERATION
• Connect the cable (#4 p.5) to the power supply.
• Properly line up notch and groove, push cable in firmly before closing screw collar.
• Place the DOLPHIN in the pool. Fig. E.
• Rock from side to side, releasing trapped air, until the DOLPHIN sinks slowly to the bottom
of the pool.
• Connect the power supply to a protected grounded outlet and switch on.
Caution: Do not operate the DOLPHIN out of water. This may result in extensive damage to the
pump motor seals, thus voiding the warranty.
• Optimum water temperature for the DOLPHIN is 64˚F-90˚F (18 ˚C-32 ˚C).
C
E
B
D
Fig
Fig
Fig
Fig
For DOLPHIN caddy assembly
see page 4
A
Fig
1
G. F. I.
Minimum 3 m. [10 ft]

Dolphin 3001 Specifications

General

Model	Dolphin 3001
Type	Robotic Pool Cleaner
Weight	16.5 lbs
Pool Type	In-ground
Warranty	2 years
Power Supply	Standard 110V

Summary

Dolphin Caddy Assembly

Caddy Assembly Instructions

Step-by-step guide for assembling the Dolphin robotic pool cleaner caddy.

Installation Guidelines

Instructions for positioning the caddy and power supply relative to the pool.

Handle Adjustment

Details on the Dolphin's adjustable handle and its optimal diagonal position.

Pool Operation

Procedure for placing the Dolphin in the pool and initiating the cleaning cycle.

Post-Cleaning Procedures

Automatic Shut Down

Information on the Dolphin's automatic shutdown after a work cycle.

Cleaning the Dolphin

Steps for removing the filter bag, cleaning it, and reassembling the unit.

Maintenance of Moving Parts

Guidance on cleaning roller brushes and the impeller.

Storage Recommendations

Instructions for storing the Dolphin on its caddy in a dry, shaded area.

Important Tips and Specifications

Operational Tips

Advice on filter bag maintenance, brush replacement, and pool obstacles.

General Specifications

Technical data including ground speed, scanning rate, and suction rate.

Power Supply Details

Specifications for the primary and secondary voltage and rated output.

Troubleshooting Dolphin Issues

Common Symptoms and Causes

Lists symptoms like climbing too high, moving in circles, or not reaching areas.

Corrective Actions

Provides solutions for issues such as filter bag clogging or impeller blockage.

Support Contact Information

Details for contacting customer support for further assistance.