Domo DO937DV User Manual

24
DO937DV
DE
· Montieren Sie den Gri.
16
· Lassen Sie das Gerät nach dem Aufstellen 2 Stunden stehen, bevor Sie es einschalten. So kann sich das
Kühlmittel verteilen.
· Schalten Sie danach das Gerät 6 Stunden lang ohne Lebensmittel ein, damit der Gefrierschrank die
erwünschte Temperatur erreichen kann.
ÖFFNUNGSRICHTUNG DER TÜR ÄNDERN
Der Türanschlag des Gefrierschranks kann verändert werden. Wenn Sie die Scharniere der Tür auf die
andere Seite versetzen möchten, empfehlen wir, einen anerkannten Fachmann zu kontaktieren und ihn
diese Arbeiten durchführen zu lassen. Bevor Sie die Önungsrichtung ändern, kontrollieren Sie, ob der
Stecker aus der Steckdose gezogen wurde und dass das Gerät leer ist.
1. Entfernen Sie die Schrauben der oberen Abdeckung.
Reverse Door
Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
 Ensure the unit is unplugged and empty.
 To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
 All parts removed must be saved to do the reinstallation of the door.
 Do not lay the unit flat as this may damage the coolant system.
 It' s better that 2 people handle the unit during assembly.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew
2. Entfernen Sie die obere Abdeckung vom Gefrierschrank.
Reverse Door
Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
 Ensure the unit is unplugged and empty.
 To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
 All parts removed must be saved to do the reinstallation of the door.
 Do not lay the unit flat as this may damage the coolant system.
 It' s better that 2 people handle the unit during assembly.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew
3. Entfernen Sie die Schrauben und anschließend das obere Scharnier, dass die Tür in ihrer Position
hält. Heben Sie die Tür hoch und legen Sie diese zur Vermeidung von Kratzern auf inen weichen
Untergrund.
Reverse Door
Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
 Ensure the unit is unplugged and empty.
 To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
 All parts removed must be saved to do the reinstallation of the door.
 Do not lay the unit flat as this may damage the coolant system.
 It' s better that 2 people handle the unit during assembly.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew

Domo DO937DV Specifications

General

Brand	Domo
Model	DO937DV
Category	Freezer
Language	English