DECLARATION OF COMPLIANCE
STATEMENT OF COMPLIANCE TO REGULATIONS (EC) No 1935/2004
ON MATERIALS AND ARTICLES INTENDED TO COME INTO CONTACT WITH FOOD
(as per Article 16 of REGULATION (EC) No 1935/2004)
Wilden
®
Pump & Engineering, LLC, 22069 Van Buren Street, Grand Terrace, CA 92313-5607 USA, declares
the equipment listed below intended to come into contact with food comply with the requirements of Regulation
(EC) No 1935/2004 of 27
th
October 2004 and (EC) No 2023/2006 of 22
nd
December 2006.
Saniflo™ HS Models:
(PX,XPX)(2,4,8,15)/(SS,SZ)(SSS,NNN)/(BNU,EPU,FBS,FES,FSS,FWL,FWS,LEL,TEU,TSS,TSU,TWS,ZSS)/
(FB,FE,FS,FV,FW,SF,TF,TM)/(FB,FE,FV,TF)/(0770-0789)E
13 mm (½”) FDA Pro-Flo
®
& Pro-Flo X™ Models:
(P,PX,XPX)1/(SS,SZ)(AAA,GGG,JJJ,LLL,PPP)/(FSS,TEU,TSU)/(FS,TF)/S(FS,TF)/(0067,0070,0120)E
25 mm (1”) FDA Pro-Flo
®
Models:
P2/(SS,SZ)(LLL,PPP)/(FBS,FES,FSS,FWL,FWS,LEL,TEU,TSS,TSU,TWS)/(FS,TF)/S(FS,TF)/2070E
38 mm (1-½”) FDA Pro-Flo
®
& Pro-Flo X™ Models:
(P,PX,XPX)4/(SS,SZ)(A,C,L,N,S,V)(AA,LL,NN,PP,SS)/(BNU,EPU,FBS,FES,FSS,FWL,FWS,LEL,TEU,TSS,TSU,TWS,ZSS)/
(FB,FE,FS,FV,FW,TF,)/(FS,FW,STF)/(0067,0070,0075,0120)E
51 mm (2”) FDA Pro-Flo
®
& Pro-Flo X™ Models:
(P,PX,XPX)8/SS(A,C,N,S,V)(AA,NN,PP,SS)/(BNU,EPU,FBS,FES,FSS,FWS,FWL,TEU,TSU,TSS,TWS,ZSS)/(FS,FW,TF)/
(FS,FW,STF)/(0070,0075,0120)E
76 mm (3”) FDA Pro-Flo X™ Models:
(PX,XPX)15/SS(A,C,N,S)(AA,SS,PP)/(BNU,EPU,FSS,FWS,TEU,TSU,TSS,TWS,ZSS)/(FS,FW,TF)/(FS,FW,STF)/
(0070,0075,0120,0341)E
38 mm (1-½”) FDA Pro-Flo
®
SHIFT Models:
XPS4/(SS,SZ)(AAA,NNN)/(FBS,FES,FWL,FWS,TSS,TWS.ZSS)/(FS,FW,TF)/(FS,FW,STF)/(0067,0070,0075,0120)E
51 mm (2”) FDA Pro-Flo
®
SHIFT Models:
XPS8/(SS,SZ)(AAA,NNN)/(FBS,FES,FWL,FWS,TSS,TWS.ZSS)/(FS,FW,TF)/(FS,FW,STF)/(0070,0075,0120)E
76 mm (3”) FDA Pro-Flo
®
SHIFT Models:
XPS15/( SS,SZ)(AAA,NNN)/(FWS,TSS,TWS,ZSS)/(FS,FW,TF)/(FS,FW,STF)/(0070,0120,0341)E
Materials used in the equipment that are intended to contact food belong to the groups of materials listed in Annex 1 (EC) 1935/2004.
(List of groups of materials and articles that may be covered by specific measures)
5) Rubbers
8) Metal and Alloy 10) Plastics
Compliance is subject to material and equipment storage, handling and usage recommended by Wilden
®
in the engineering
operation and maintenance manual and supplemental technical publications.
This declaration is based on the following information:
Statements of raw material suppliers
Wilden
®
will make available to the competent authorities appropriate documentation to demonstrate compliance.
Approved By:
Chris Distaso
Director of Engineering
Date: March 21, 2014
To Next Page
Loading...
