-4-
LIMITLESS 5
®
Flight Tutorial Video
Press and hold the “headless mode” key for 5
seconds. The remote control will make a “BEEP”
sound, indicating that GPS function is turned OFF.
This will allow take-off while in ATTI MODE.
1. Open your phone’s
camera
2. Focus on the QR Code
without taking a photo.
3. Click on the pop-up link
that appears.
ATTI MODE (aka “INDOOR MODE” or “Optical Flow Mode”): Is applicable to large indoor open places, such as a spacious gym.
The default settings are programmed for the automated protection program to prevent the drone from taking flight until the system connects to
enough satellites to enter GPS MODE; however, if the user wants to fly indoors (in ATTI Mode) the user can simply override this automated
failsafe protection, and by doing so, won’t have to wait for a strong GPS satellite connection in order to take flight. But before you do this, make
sure the drone and remote control are synced with each other, and that you’ve calibrated the drone successfully by following instructions for
“geomagnetic & gyroscope calibration”.
To fly in ATTI MODE, simply override the protection failsafe by pressing / holding the headless mode key for 5 seconds on the remote control
(see photo below for location of this key). The remote control will emit a "BEEP" sound, and the remote’s LCD display screen will change from
“POSITIONING“ to “ATTI MODE”, which means the failsafe is OFF and the drone is now able to take flight indoors.
IMPORTANT NOTE: When in ATTI MODE, the drone will NOT have GPS safety features, including Auto Return Home functions, such as “low
power return”, “1-key return”, etc. Please pay attention to the flight distance and altitude when flying in ATTI MODE. This is the reason why we
suggest the drone should only be flown indoors when in ATTI MODE since the drone does NOT have GPS capabilities when in ATTI MODE. In
order for GPS “Return To Home” (RTH) Functions to be activated, you must fly in GPS MODE. If flown outside in ATTI Mode, you assume all
risk and are responsible if your drone is lost or crashes.
GPS MODE: Programmed for OUTDOOR flight in open areas that are free from signal interference. After the drone and remote control are
synced with each other (takes about 40 secs) you’ll notice the remote LCD display changes from “CONNECTING” to “POSITIONING”. At this
time, the drone begin searching for a strong satellite signal. The drone will enter GPS MODE after a couple minutes once it’s gained at least 8
sattelites, which will be shown on your remote’s LCD display. You must be outside with a clear view of the sky. While waiting for the drone to
gain 8 or more satellites, calibrate the drone by following instructions for “geomagnetic & gyroscope calibration. There should be no
obstructions such as high-rise buildings or cars, high-voltage power lines, etc., otherwise the drone may not be able to complete GPS satellite
search and positioning. When 8-10 satellites are gained, GPS positioning is complete, which is indicated by a ”BEEP” sound from the remote
control, and the LCD display screen changes from “POSITIONING” to “GPS MODE”. You can now unlock the drone motors and take flight in
GPS mode.
IMPORTANT NOTE: If the drone does not gain enough satellites to enter GPS MODE, then the drone will NOT take-off. This is a built in
failsafe to prevent users from taking flight outside of GPS mode. If the user takes off before entering GPS mode by overriding this protective
failsafe, then keep in mind the drone won’t know where to return home to if an issue arrises, such as loss of signal, low battery, etc.
ATTI MODE
Drone-Clone Xperts
ATTI MODE / Indoor Mode: is also known as “Optical Flow Mode”. We suggest you never fly in this mode unless you are inside in a WIDE-OPEN
gym ot other large infoor facility, because GPS is not active and therefore Auto Return Home functions are not available in ATTI Mode. Additionally,
the drone is not nearly as stable in this mode. When the drone is not stable and does not record where the home point is, this can lead to damage
or loss of drone if outside. This is why we only suggest flying in GPS Mode. However, if you understand and accept responsibility for the risks
mentioned and decide to fly in ATTI Mode, you’ll first have to disable the safety failsafe by turning off GPS function. Once you’ve successfully
turned off GPS function, you’ll then be able to take-off successfully without needing to gain 10 satellites.
GPS Mode: is the default mode upon startup. It takes about 2-5 mins to acquire a strong GPS Satelite signal. Once your remote’s display screen
and/or LIMITLESS 5 APP shows 10 satelites, this indicates a strong enough GPS connection to attempt take-off.
You must be outdoors in an open area to get a strong enough GPS signal. Stay AWAY from high-voltage wires & other signal interference.
Scan QR code below to view the important L5 INSTRUCTION VIDEO to gain a much better understanding of these 2 modes as well as the many
other features / functions LIMITLESS 5 has to offer. Also note there’s more detailed information about these modes explained below
ViewInstructionVIDEO:
To Next Page
Loading...
Need help?
General
