36
Section PGM Output 1 2 3 4 5 6 7 8
#Type*
[141] 1 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[142] 2 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
*Record here based on programming in [009].
[160] Maximum Dialing Attempts to Each Telephone Number
(Section 5.5 “Communicator – Dialing” on page 17)
Default: 008 I_______I_______I_______I Valid entries are 001-015 attempts (do not enter 000).
[161] Post Dial Wait for Handshake (All Formats)
(Section 5.5 “Communicator – Dialing” on page 17)
Default: 040 I_______I_______I_______I Valid entries are 001-255 seconds
[164] PGM Output Timer
(Section 5.5 “Communicator – Dialing” on page 17)
Default: 005 I_______I_______I_______I Valid entries are 001-255 seconds
[202] Zone Assignments 01-08
(Section 5.2 “Zone Programming” on page 15)
Program zone definitions in sections [001] - [004] and zone attributes in sections [101] - [132]. Program keypad zone assignments
in section [020].
NOTE:Any zones not used on the system should be disabled in this section. Disabled wireless zones should have a blank serial
number (i.e. [000000]).
Zones 1-8: Default = ON; Zones 9-32: Default = OFF
Section Option: 1 2 3 4 5 6 7 8
[202] Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I
[203] Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I
[204] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I
[205] Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I
Communicator Programming
NOTE: For sections [301] to [353], the content of every section by default is [F].
[301] First Telephone Number (32 Digits) (Section 5.7 “Communicator – Telephone Numbers” on page 17)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[302] Second Telephone Number (32 Digits) (Section 5.7 “Communicator – Telephone Numbers” on page 17)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[303] Third Telephone Number (32 Digits) (Section 5.7 “Communicator – Telephone Numbers” on page 17)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[310] First/Third Telephone Number Account Code (Section 5.6 “Communicator – Account Numbers” on page 17)
I_______I_______I_______I_______I
[311] Second Telephone Number Account Code (Section 5.6 “Communicator – Account Numbers” on page 17)
I_______I_______I_______I_______I
To Next Page
Loading...
