DSC PC1555

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls Ltd. could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. How-
ever, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
‘ Re-orient the receiving antenna.
‘ Increase the separation between the equipment and receiver.
‘ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‘ Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: “How to
Identify and Resolve Radio/Television Interference Problems”. This booklet is
available from the U.S. Government Printing Office, Washington D.C. 20402,
Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of
this equipment is a label that contains, among other information, the
FCC registration number of this equipment.
Notification to Telephone Company The customer shall notify the tele-
phone company of the particular line to which the connection will be
made, and provide the FCC registration number and the ringer equiva-
lence of the protective circuit.
FCC Registration Number: F53CAN-32028-AL-E
Facility Interface Code: 02LS2
Ringer Equivalence Number: 0.1B
Service Order Code: 9.0F
USOC Jack: RJ31X
Telephone Connection Requirements Except for the telephone company
provided ringers, all connections to the telephone network shall be made
through standard plugs and telephone company provided jacks, or equiva-
lent, in such a manner as to allow for easy, immediate disconnection of the
terminal equipment. Standard jacks shall be so arranged that, if the plug
connected thereto is withdrawn, no interference to the operation of the
equipment at the customer’s premises which remains connected to the tele-
phone network shall occur by reason of such withdrawal.
Incidence of Harm Should terminal equipment or protective circuitry cause
harm to the telephone network, the telephone company shall, where practi-
cable, notify the customer that temporary disconnection of service may be
required; however, where prior notice is not practicable, the telephone com-
pany may temporarily discontinue service if such action is deemed reason-
able in the circumstances. In the case of such temporary discontinuance,
the telephone company shall promptly notify the customer and will be given
the opportunity to correct the situation.
Additional Telephone Company Information The security control panel
must be properly connected to the telephone line with a USOC RJ-31X tele-
phone jack.
The FCC prohibits customer-provided terminal equipment be connected to
party lines or to be used in conjunction with coin telephone service. Intercon-
nect rules may vary from state to state.
Changes in Telephone Company Equipment or Facilities The telephone
company may make changes in its communications facilities, equipment,
operations or procedures, where such actions are reasonably required and
proper in its business. Should any such changes render the customer’s ter-
minal equipment incompatible with the telephone company facilities the cus-
tomer shall be given adequate notice to the effect modifications to maintain
uninterrupted service.
Ringer Equivalence Number (REN) The REN is useful to determine the
quantity of devices that you may connect to your telephone line and still have
all of those devices ring when your telephone number is called. In most, but
not all areas, the sum of the RENs of all devices connected to one line should
not exceed five (5.0). To be certain of the number of devices that you may
connect to your line, you may want to contact your local telephone company.
Equipment Maintenance Facility If you experience trouble with this tele-
phone equipment, please contact the facility indicated below for information
on obtaining service or repairs. The telephone company may ask that you
disconnect this equipment from the network until the problem has been cor-
rected or until you are sure that the equipment is not malfunctioning.
Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094
UL Listed Commercial and Residential Installations
The installation requirements listed below must be met for the following
grades of service.
Grade A Local
The installation must have a bell UL Listed for mecantile local alarms
(AMSECO MBL10B with model AB-12 bell housing).
The digital communicator must be enabled.
The control panel must be in the Attack Resistant Enclosure (DSC Model
CMC-1).
Swinger shutdown must be disabled.
Grade B Central Station and Police Connect
The installation must have a bell UL Listed for mecantile local alarms
(AMSECO MBL10B with model AB-12 bell housing).
The digital communicator must be enabled.
Ringback must be enabled.
The control panel must be in the Attack Resistant Enclosure (DSC Model
CMC-1).
Swinger shutdown must be disabled.
Grade C Central Station
The digital communicator must be enabled.
Ringback must be enabled.
The control panel must be in the Attack Resistant Enclosure (DSC Model
CMC-1).
Swinger shutdown must be disabled.
All Commercial Installations
• The entry delay must not exceed 60 seconds
• The exit delay must not exceed 60 seconds.
• The minimum bell cutoff time is 15 minutes.
Residential Installations
• The entry delay must not exceed 45 seconds
• The exit delay must not exceed 60 seconds.
• The minimum bell cutoff time is 4 minutes.
Programming
The notes in the programming sections describing the system configura-
tions for UL Listed installations must be implemented.
Control of the Protected Premises
In order to have a UL Certificated system the protected area is to be
under the responsibility of one ownership and management (i.e. one
business under one name). This may be a group of buildings attached or
unattached with different addresses but under the responsibility of
someone having mutual interest. The person of mutual interest is not the
alarm installing company.
Bell Location
The alarm sounding device (bell) must be located where it can be heard
by the person or persons responsible for maintaining the security system
during the daily arming cycle.
Protection of the Control Unit
The local control and the local power supply must be protected by one of
the following ways:
• The control unit and audible alarm device power supply must be in a
protected area which is armed 24 hours a day.
• Each partition shall arm the area protecting the control unit and the
audible alarm device power supply. This may require duplicate pro-
tection armed by each partition. Access to this protected area, with-
out causing an alarm, will require that all partitions be disarmed.
In all cases described above, the protected area for the control unit must
be programmed as not bypassable.
Casual Users
The installer should caution the user(s) to not give system information to
casual users (e.g. codes, bypass methods, etc. to baby-sitters or service
people). Only the One-Time Use codes should be given to casual users.
User Information
The installer should advise the users and note in the user instruction
manual:
• Service organization name and telephone number
• The programmed exit time
• The programmed entry time