Dyna-Glo M486BBDG14 User Manual (English)

Questions and Answers:

L
Lisa ClementsAug 16, 2025
What to do if the Dyna-Glo M486BBDG14 Grill burner will not light with a match?
- S
  Stephen NicholsAug 16, 2025
  If the burner on your Dyna-Glo Grill won't light with a match, there are several potential causes. First, ensure the match is reaching the burners by using the match holder found in the cabinet door. Also, check the fuel level and refill the tank if necessary. Another potential issue is a poor connection between the valve regulator and LP cylinder coupling; in this case, turn off the grill knobs, close the LP cylinder valve, and check the connection, disconnecting and reconnecting if needed. Finally, the burner inlet may be blocked, so clean the burner inlet (venturi) and burner.
J
justinbrownAug 19, 2025
How to fix a Dyna-Glo Grill burner that will not light using the ignitor?
- S
  Samantha JacobsAug 19, 2025
  If the burner on your Dyna-Glo Grill won't light using the ignitor, it could be due to several reasons. The igniter electrode may be covered with grease or residue, so clean the ignitor electrode. Also, the igniter electrode may have a loose or disconnected wire, so check the connection and reconnect any loose or disconnected wires. Other potential causes include a cracked or broken ignition electrode (replace ignition electrode) or a dead/faulty battery (replace the battery, ensure it's inserted correctly, check for corrosion, and check wire connections).
N
Nicole GibsonAug 22, 2025
Why is my Dyna-Glo M486BBDG14 producing low heat?
- C
  Cheryl JarvisAug 22, 2025
  Insufficient gas pressure to the unit could be the reason your Dyna-Glo Grill is producing low heat. Call a qualified service agency to check the gas supply pressure and correct the pressure.
C
Charles WeberAug 26, 2025
What to do if Dyna-Glo M486BBDG14 Grill burner won't light with ignitor?
- S
  Spencer SmithAug 26, 2025
  If the burner on your Dyna-Glo Grill won't light using the ignitor, it could be due to several reasons: 1. The igniter electrode may be covered with grease or residue. Clean the ignitor electrode. 2. The igniter electrode may have a loose or disconnected wire. Check the connection and reconnect any loose or disconnected wires. 3. Cracked or broken ignition electrode. Replace the ignition electrode. 4. Dead battery or faulty battery connection. Replace the battery, ensure it's inserted correctly, check for corrosion around the terminals, and check wire connections.
J
Jonathan WrightAug 28, 2025
How to light Dyna-Glo M486BBDG14 with a match?
- T
  Travis WagnerAug 28, 2025
  If your Dyna-Glo Grill burner won't light with a match, consider these possibilities: 1. The match may not be reaching the burners. Use the match holder found in the cabinet door. 2. The tank may be empty. Check the fuel level and refill the tank if necessary. 3. There might be a poor connection between the valve regulator and LP cylinder coupling. Turn off the grill knobs, close the LP cylinder valve, and check the connection. Disconnect and reconnect if necessary. 4. The burner inlet could be blocked. Clean the burner inlet (venturi) and burner as described in the Care and Maintenance section.
K
Kevin WhiteAug 31, 2025
Why does my Dyna-Glo Grill have low heat?
- J
  Jesus BakerAug 31, 2025
  Low heat in your Dyna-Glo Grill may be due to insufficient gas pressure to the unit. Call a qualified service agency to check the gas supply pressure and correct the pressure.
D
Darlene MoraSep 3, 2025
Why are there excessive flare ups on my Dyna-Glo M486BBDG14 Grill?
- H
  Howard BarberSep 3, 2025
  Excessive flare-ups on your Dyna-Glo Grill can occur due to a few reasons: build-up of grease and/or residue on heat tents or in the firebox (clean the grill components); excessive dripping of fat or marinade from food (trim the fat from meat and use non-oil based marinades); or a cooking temperature that is too high (lower the temperature accordingly).
M
Morgan CisnerosSep 6, 2025
What to do if there is no gas flow in Dyna-Glo Grill?
- A
  Alexander GainesSep 6, 2025
  If you're experiencing no gas flow or an obstructed gas flow in your Dyna-Glo Grill, start by ensuring the tank valve is fully opened by turning it counterclockwise. Check the fuel level and replace the fuel if necessary. A poor connection between the valve regulator and LP cylinder coupling could also be the culprit; turn off grill knobs, close the LP cylinder valve, and check/reconnect the connection if needed. Lastly, a blocked burner inlet could be the cause; clean the burner inlet (venturi) and burner.
N
Nichole BurtonSep 9, 2025
Why does my Dyna-Glo M486BBDG14 have excessive flare ups?
- K
  kingsandySep 9, 2025
  Excessive flare-ups in your Dyna-Glo Grill can occur due to: * Grease and/or residue build-up on heat tents or in the firebox. Clean the grill components to resolve this. * Excessive dripping of fat or marinade from food. Trim the fat from meat and use non-oil based marinades. * Cooking temperature being too high. Lower the temperature accordingly.
Z
zallenSep 12, 2025
Why is there no gas flow in my Dyna-Glo Grill?
- M
  Maria WalkerSep 12, 2025
  If you're experiencing no gas flow or an obstructed gas flow in your Dyna-Glo Grill, it could be due to: 1. The tank valve not being on or fully opened. Fully open the tank valve by turning it counterclockwise. 2. An empty tank. Check the fuel level and replace the fuel if necessary. 3. A poor connection between the valve regulator and LP cylinder coupling. Turn off the grill knobs, close the LP cylinder valve at the top of the cylinder, and check the connection. Disconnect and reconnect if necessary. 4. A blocked burner inlet. Clean the burner inlet (venturi) and burner as described in the Care and Maintenance section.

Dyna-Glo M486BBDG14 Specifications

General

Model	M486BBDG14
Type	Gas Grill
Number of Burners	4
Fuel Type	Propane
Color	Black
Cooking Area	486 sq. in.
Material	Stainless steel
Warranty	1 year limited
BTU	48, 000 BTU