Exerferi busapellab ius assin conserchil est, temperibus nihi-
caboris et autem volupta eturecto excerem repe volupta peliquis
mi, quasi optae. Lia cum ulpa verorro conem rectotatur assimu-
sae. Itatio. Quaspedi dellorum vendaer spicimod esed quo debit
enimet aut ut fugiae inveles es vercimpel idenestio ipsandia et
ute plitat.
Ces dolutem quisquatur?
Bus ex ent vollacestia sitam, id utate nonet lit quis consent
veremporia aute vit occust laut a por aperum et a veritia experru
mquodi ut laborru ntorerum eum seque volecestio. Ut quo occab
id ut maio. Bus molupta temoluption cuptatentur, erum dolupis
quaspis doluptas qui ommodion prepers pedionsequia ipsam
audaeribus aut autectatur?
Dandus dolorrum sa premo mint, nusdae excestia quas denis
pori imus que viducid emporiti il iumquo od quisque nost voleni
solorero is aut id que modicit latur?
Right Page Header
57
SC-14
56
Exerferi busapellab ius assin conserchil est, temperibus nihi-
caboris et autem volupta eturecto excerem repe volupta peliquis
mi, quasi optae. Lia cum ulpa verorro conem rectotatur assimu-
sae. Itatio. Quaspedi dellorum vendaer spicimod esed quo debit
enimet aut ut fugiae inveles es vercimpel idenestio ipsandia et
ute plitat.
Ces dolutem quisquatur?
Bus ex ent vollacestia sitam, id utate nonet lit quis consent
veremporia aute vit occust laut a por aperum et a veritia experru
mquodi ut laborru ntorerum eum seque volecestio. Ut quo occab
id ut maio. Bus molupta temoluption cuptatentur, erum dolupis
quaspis doluptas qui ommodion prepers pedionsequia ipsam
audaeribus aut autectatur?
Dandus dolorrum sa premo mint, nusdae excestia quas denis
pori imus que viducid emporiti il iumquo od quisque nost voleni
solorero is aut id que modicit latur?
Left Page Header
SC-14
• Sharpen damaged teeth back to undamaged part. Sharpen rest of teeth to
the same length.
• Always sharpen the side with the shortest teeth rst. To determine this,hold
the saw-chain with your left hand, now take hold of the bottom of the chain
with your right hand, next bring your right hand up to your left hand, com-
pare the left-hand tooth to the right-hand tooth. Now nd the shortest or
most damaged tooth on the shortest side. Sharpen this tooth, then sharpen
the rest at the same length.
• Always keep cutters at the same length. Due to inaccuracy of your grind-
er you will need to check your chain after you sharpen the rst tooth of the
second side. Check to see if it is the same length as the rst side by using
the procedure noted in above section.
• Setting the depth gauge. Sharpen the tooth before ling the depth gauge.
Use an .050 Oregon® depth gauge tool for .404 18HX saw-chain. Check
your chain every 3-4 sharpening. Place the tool on top of the saw-chain
so that one depth gauge protrudes through the slot in the tool. If the depth
gauge extends above the slot, le it down level with the tool with a at hand
le or the intended grinding wheel (included with the grinder). File from the
inside of the round ground saw-chain teeth to the outside. See in Fig 1
Continued Chain Maintenance/Sharpening
AIR-INNER SAFETY (36-40
HP)
SC-14D – SC-15D – SC-16
29-44 HP KUBOTA
SC-14D – SC-15D 34 HP
CAT
***ALL MODELS TAKE AW46 HYDRAULIC OIL***
Inside
Outside
Fig. 1
To Next Page
Loading...