WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
WMV-Dresden
SAFETY INSTRUCTIONS
Carefully Read all instructions before operating or servicing any Dynabrade
®
Abrasive Power Tool.
Products offered by Dynabrade are not to be modified, converted or otherwise altered from the original design without expressed written consent from Dynabrade, Inc.
Tool Intent: Dynafile
®
abrasive belt machine replaces tedious hand filing and sanding and can be used for grinding, deburring, blending and polishing. Tool can be used on most
materials including metal, plastic, fiberglass, composites, rubber, glass and stone.
Do not use tool for anything other than its intended applications.
This power tool is not intended for use in potentially explosive atmospheres and is not insulated against contact with electrical power.
Training: Proper care, maintenance, and storage of your tool will maximize its performance.
• Employer's Responsibility – Provide Dynafile
®
operators with safety instructions and training for safe use of tools and accessories.
Accessory Selection:
• Abrasive/accessory RPM (speed) rating MUST be approved for AT LEAST the tool RPM rating.
• Before mounting an accessory, visually inspect for defects. Do not use defective accessories.
• Mount only recommended accessories. See manual and Dynabrade catalog.
• Follow tool specifications before choosing size and type of accessory.
• Only use recommended fittings and air line sizes. (See tool Machine Specifications table.)
OPERATING INSTRUCTIONS
Warning: Always wear eye protection. Operator of tool is responsible for following: accepted eye, face, respiratory, hearing and body protection.
Caution: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
• Only use recommended fittings and air line sizes. Air supply hoses and air hose assemblies must have a minimum working pressure rating of 150 PSIG
(10 Bars, g) or 150 percent of the maximum pressure produced in the system, whichever is higher. (See tool Machine Specifications table.)
(continued on next page)
PD05•13R
November, 2016
Supersedes PD05•13
Dynafile
®
Air Tool Manual – Safety, Operation and Maintenance
Models:
14000 – 20,000 RPM
14010 – Versatility Kit
SAFETY LEGEND
Read and understand tool manual before
work starts to reduce risk of injury to
operator, visitors, and tool.
Eye protection must be worn at all times,
eye protection to conform to ANSI Z87.1.
Respiratory protection to be used when exposed to
contaminants that exceed the applicable threshold
limit values required by law.
Practice safety requirements. Work alert,
have proper attire, and do not operate tools under
the influence of alcohol or drugs.
Ear protection to be worn when exposure to sound,
exceeds the limits of applicable Federal, State or
local statues, ordinances and/or regulations.
Air line hazard, pressurized supply lines and flexible
hoses can cause serious injury. Do not use damaged,
frayed or deteriorated air hoses and fittings.
Read and understand this tool manual before operating your air tool. Follow all safety rules for the protection of operating personnel
as well as adjacent areas. Always operate, inspect and maintain this tool in accordance with the American National Safety Institute
(ANSI) Safety Code for Portable Air Tools – B186.1. For additional safety information, refer to Safety Requirements for the Use, Care
and Protection of Abrasive Wheels – ANSI B7.1, Code of Federal Regulation – CFR 29 Part 1910, European Committee for Standards
(EN) Hand Held Non-Electric Power Tools – Safety Requirements and applicable State and Local Regulations.
SAVE THIS DOCUMENT, EDUCATE ALL PERSONNEL
For Serial No. 4A1000 and Higher
WMV-Dresden, Ersatzteilservice für Elektrowerkzeuge, Motor- und Gartengeräte
WMV-Dresden, Ersatzteilservice für Elektrowerkzeuge, Motor- und Gartengeräte
WMV-Dresden, Ersatzteilservice für Elektrowerkzeuge, Motor- und Gartengeräte
To Next Page
Need help?
General