What to do if Eaton 9E 10000i beeps and shows A80E, A810, or F808?
If your Eaton UPS buzzer sounds continuously and the display shows code A80E, A810, or F808, the load applied to the UPS is too high. Reduce the load to within 100% of the threshold (or the user threshold in the case of code A80E). If the display shows a fault, remove the load and switch the UPS off and back on again.
What does it mean when Eaton 9E 10000i UPS beeps and shows code F805?
If the buzzer of your Eaton UPS is sounding continuously and the display shows code F805, there is a fault on one or more of the loads powered by the UPS. To resolve this, disconnect all the utilities, switch the UPS off and back on again. Then, reconnect the utilities one at a time to identify the faulty one.
Why does my Eaton 9E 10000i UPS beep and show A004 or F004?
If your Eaton UPS buzzer sounds continuously and the display shows code A004 or F004, the temperature inside the UPS is too high. Make sure the environment where the UPS is located does not exceed 40°C.
What to do if my Eaton 9E 10000i display does not light up?
If the display of your Eaton UPS doesn't light up, here's what you can check: * Ensure the input switch on the back of the UPS is closed. * Verify the power cable is correctly connected. * Confirm that power is reaching the UPS, and there is no blackout. * Check for and reset any upstream thermal protection trips. Be cautious of potential output overloads to the UPS.
What to do if my Eaton 9E 10000i UPS buzzer sounds continuously and shows codes A004 or F004?
If your Eaton UPS buzzer sounds continuously and the display shows code A004 or F004, it means the temperature inside the UPS is too high. Check that the temperature of the environment in which the UPS is located does not exceed 40°C.
What to do if my Eaton UPS buzzer sounds continuously and shows code F805?
If your Eaton UPS buzzer sounds continuously and the display shows code F805, it indicates a fault on one or more of the loads powered by the UPS. Disconnect all the utilities, switch the UPS off and back on again, and then reconnect the utilities one at a time to identify which one is faulty.
Why is my Eaton 9E 10000i running on battery when plugged in?
If the Eaton UPS is operating from the battery even when mains voltage is present, it's likely that the input voltage is outside the acceptable range for mains operation. The solution is to wait for the mains voltage to return within the tolerance range. The UPS will then automatically switch back to mains operation.
What does A60D code mean on Eaton UPS?
If the display of your Eaton UPS shows code A60D, it means batteries or battery box are missing or not connected. Check that the battery box is correctly inserted and connected to the UPS.
What to do if Eaton 9E 10000i display is on but no power to load?
If the display is on but the load is not powered by your Eaton UPS, the UPS might be in standby mode. Press the 'ON' button on the front panel to power the loads.
What does A900 mean on my Eaton 9E 10000i UPS display?
If the display of your Eaton UPS shows the code A900, the maintenance bypass function is active. To deactivate it, open the manual bypass switch on the back of the UPS.
General| Output Power Factor | 0.9 |
|---|---|
| Topology | Double Conversion Online |
| Output Voltage THD | < 3% |
| Form Factor | Tower |
| Frequency Range | 50/60 Hz |
| Operating Temperature | 0 to 40 °C |
| Power Rating | 10000 VA |
| Input Voltage | 220/230/240 VAC |
| Output Voltage | 220/230/240 VAC |
| Battery Type | Sealed Lead-Acid (SLA) |
| Communication | USB, RS232 |
| Transfer Time | 0 ms |
| Operating Humidity | 0-95% non-condensing |
To Next Page
