What to do if Eaton UPS beeps and shows A80E, A810, or F808?
If your Eaton UPS buzzer sounds continuously and the display shows code A80E, A810, or F808, the load applied to the UPS is too high. Reduce the load to within 100% of the threshold (or the user threshold in the case of code A80E). If the display shows a fault, remove the load and switch the UPS off and back on again.
What does it mean when Eaton 9E15Ki beeps and shows code F805?
If the buzzer of your Eaton UPS is sounding continuously and the display shows code F805, there is a fault on one or more of the loads powered by the UPS. To resolve this, disconnect all the utilities, switch the UPS off and back on again. Then, reconnect the utilities one at a time to identify the faulty one.
Why does my Eaton 9E15Ki UPS beep and show A004 or F004?
If your Eaton UPS buzzer sounds continuously and the display shows code A004 or F004, the temperature inside the UPS is too high. Make sure the environment where the UPS is located does not exceed 40°C.
What to do if my Eaton 9E15Ki display does not light up?
If the display of your Eaton UPS doesn't light up, here's what you can check: * Ensure the input switch on the back of the UPS is closed. * Verify the power cable is correctly connected. * Confirm that power is reaching the UPS, and there is no blackout. * Check for and reset any upstream thermal protection trips. Be cautious of potential output overloads to the UPS.
What to do if my Eaton UPS buzzer sounds continuously and shows codes A004 or F004?
If your Eaton UPS buzzer sounds continuously and the display shows code A004 or F004, it means the temperature inside the UPS is too high. Check that the temperature of the environment in which the UPS is located does not exceed 40°C.
What to do if my Eaton 9E15Ki UPS buzzer sounds continuously and shows code F805?
If your Eaton UPS buzzer sounds continuously and the display shows code F805, it indicates a fault on one or more of the loads powered by the UPS. Disconnect all the utilities, switch the UPS off and back on again, and then reconnect the utilities one at a time to identify which one is faulty.
Why is my Eaton 9E15Ki UPS running on battery when plugged in?
If the Eaton UPS is operating from the battery even when mains voltage is present, it's likely that the input voltage is outside the acceptable range for mains operation. The solution is to wait for the mains voltage to return within the tolerance range. The UPS will then automatically switch back to mains operation.
What does A60D code mean on Eaton 9E15Ki UPS?
If the display of your Eaton UPS shows code A60D, it means batteries or battery box are missing or not connected. Check that the battery box is correctly inserted and connected to the UPS.
What to do if Eaton 9E15Ki display is on but no power to load?
If the display is on but the load is not powered by your Eaton UPS, the UPS might be in standby mode. Press the 'ON' button on the front panel to power the loads.
What does A900 mean on my Eaton 9E15Ki display?
If the display of your Eaton UPS shows the code A900, the maintenance bypass function is active. To deactivate it, open the manual bypass switch on the back of the UPS.
General| Output Power Factor | 0.9 |
|---|---|
| Topology | Double Conversion Online |
| Output Frequency | 50/60 Hz |
| Form Factor | Tower |
| Power Rating | 15 kVA |
| Input Voltage | 220-240 V / 380-415 V (3:1) |
| Output Voltage | 220-240 V / 380-415 V (3:3) |
| Battery Type | Sealed lead-acid (VRLA) |
| Runtime at Full Load | 5 minutes |
| Communication | RS-232, USB |
| Expandability | External battery packs |
Essential safety guidelines for UPS installation and operation.
Lists the safety and EMC standards the UPS complies with.
Explains important symbols used on the UPS unit.
Details UPS models, ratings, and electrical system architecture.
Visual identification of front and rear components for UPS and EBMs.
Steps for unpacking the UPS and a checklist of package items.
Critical requirements for electrical installation and UPS connection.
Guide for connecting external battery boxes to the UPS.
Explanation of buttons, LCD display, and LED indicators.
Procedures for turning the UPS on, off, and managing bypass modes.
How to configure UPS parameters and communication settings.
Table of common problems, their causes, and resolutions.
List of alarm codes and their corresponding meanings.
Detailed specifications for input, output, battery, and dimensions.
To Next Page
