What to do if Eaton UPS shows power overload?
If the Power overload LED is On and the UPS beeps continuously, it means that the power requirements exceed the UPS capacity. To resolve this, remove some of the equipment from the UPS. Note that the UPS continues to operate, but may switch to Bypass mode or shut down if the load increases.
Why is the Eaton UPS battery mode LED on?
The Battery mode LED is On with 1 beep every 10 seconds because a utility failure has occurred, and the UPS is now in Battery mode. The UPS is using battery power to keep your equipment running. You should prepare your equipment for shutdown.
What to do if my Eaton UPS doesn't start?
If the Eaton UPS doesn't start, there might be several reasons. First, check the input connections to ensure the input source is correctly connected. Second, ensure that the Remote Power Off (RPO) switch is not active, and the RPO connector is properly connected. If the UPS Status menu displays the 'Remote Power Off' notice, inactivate the RPO input.
What to do if Eaton 9SX2000 UPS is overheating?
If the UPS overtemperature LED is On and it beeps every 3 seconds, it indicates that the UPS internal temperature is too high or a fan has failed. If the UPS transferred to Bypass mode, it will return to normal operation when the temperature drops 5 °C below the warning level. If the condition persists, shut down the UPS. Clear vents and remove any heat sources. Allow the UPS to cool. Ensure the airflow around the UPS is not restricted. Restart the UPS.
What to do if Eaton 9SX2000 battery fault LED is on?
If the Battery fault LED is On and the UPS beeps continuously, it indicates that the battery test failed due to bad or disconnected batteries, or the battery minimum voltage is reached in ABM® cycling mode. Verify that all batteries are properly connected. Start a new battery test.
Why Eaton 9SX2000 UPS battery low LED is on?
The Battery low LED is On and the UPS beeps every 3 seconds because the UPS is in Battery mode and the battery is running low. This warning is approximate, and the actual time to shutdown may vary significantly. Depending on the UPS load and number of Extended Battery Modules (EBMs), the 'Battery Low' warning may occur before the batteries reach 20% capacity.
How to fix Eaton 9SX2000 UPS not providing expected backup time?
If the Eaton UPS isn't providing the expected backup time, it could be that the batteries need charging or service. To address this, apply utility power for 48 hours to charge the batteries.
What to do if Eaton 9SX2000 UPS no battery LED is on?
If no battery LED is On and the UPS beeps continuously, it means that the batteries are disconnected. Verify that all batteries are properly connected.
General| Power Rating | 2000 VA |
|---|---|
| Output Power Capacity | 1800 W |
| Topology | Double Conversion Online |
| Nominal Output Voltage | 230 V |
| Output Voltage Regulation | ± 1% |
| Input Frequency | 40 - 70 Hz |
| Form Factor | Tower |
| Output Frequency | 50/60 Hz |
| Efficiency | Up to 95% |
| Outlets | 8 |
| Communication | USB |
| Network Management | Optional |
| Battery Type | Sealed Lead-Acid |
Examples of symbols used on UPS and accessories for important information.
Guidelines for safe handling, operation, and product electrical safety.
Specific safety measures for handling, installation, and maintenance.
Overview of the UPS front panel graphical LCD and its indicators.
Details on the LCD screen saver and status information provided by the UPS.
Details on programmable signal inputs and Remote Power Off (RPO) function.
Explanation of RPO connections and programmable signal outputs.
Steps for starting, starting on battery, and shutting down the UPS.
Explanation of different UPS operating modes like Online and Battery mode.
Details on warnings, bypass, AC power return, and setting High Efficiency mode.
Warnings and precautions before and during battery replacement.
Step-by-step guide for replacing internal batteries in rack-mount UPS.
Step-by-step guide for replacing internal batteries in tower UPS (0-3KVA).
Step-by-step guide for replacing internal batteries in tower UPS (5-6KVA).
Chart to diagnose common UPS alarms and faults and their solutions.
To Next Page
