What to do if Eaton 9SX700 UPS shows power overload?
If the Power overload LED is On and the UPS beeps continuously, it means that the power requirements exceed the UPS capacity. To resolve this, remove some of the equipment from the UPS. Note that the UPS continues to operate, but may switch to Bypass mode or shut down if the load increases.
Why is the Eaton 9SX700 battery mode LED on?
The Battery mode LED is On with 1 beep every 10 seconds because a utility failure has occurred, and the UPS is now in Battery mode. The UPS is using battery power to keep your equipment running. You should prepare your equipment for shutdown.
What to do if my Eaton 9SX700 UPS doesn't start?
If the Eaton UPS doesn't start, there might be several reasons. First, check the input connections to ensure the input source is correctly connected. Second, ensure that the Remote Power Off (RPO) switch is not active, and the RPO connector is properly connected. If the UPS Status menu displays the 'Remote Power Off' notice, inactivate the RPO input.
What to do if Eaton UPS is overheating?
If the UPS overtemperature LED is On and it beeps every 3 seconds, it indicates that the UPS internal temperature is too high or a fan has failed. If the UPS transferred to Bypass mode, it will return to normal operation when the temperature drops 5 °C below the warning level. If the condition persists, shut down the UPS. Clear vents and remove any heat sources. Allow the UPS to cool. Ensure the airflow around the UPS is not restricted. Restart the UPS.
What to do if Eaton UPS battery fault LED is on?
If the Battery fault LED is On and the UPS beeps continuously, it indicates that the battery test failed due to bad or disconnected batteries, or the battery minimum voltage is reached in ABM® cycling mode. Verify that all batteries are properly connected. Start a new battery test.
Why Eaton UPS battery low LED is on?
The Battery low LED is On and the UPS beeps every 3 seconds because the UPS is in Battery mode and the battery is running low. This warning is approximate, and the actual time to shutdown may vary significantly. Depending on the UPS load and number of Extended Battery Modules (EBMs), the 'Battery Low' warning may occur before the batteries reach 20% capacity.
How to fix Eaton UPS not providing expected backup time?
If the Eaton UPS isn't providing the expected backup time, it could be that the batteries need charging or service. To address this, apply utility power for 48 hours to charge the batteries.
What to do if Eaton 9SX700 no battery LED is on?
If no battery LED is On and the UPS beeps continuously, it means that the batteries are disconnected. Verify that all batteries are properly connected.
General| Power Rating | 700 VA |
|---|---|
| Output Power | 630 W |
| Output Voltage | 230 V |
| Topology | Line-interactive |
| Form Factor | Tower |
| Frequency | 50/60 Hz |
| Operating Temperature | 0 to 40 °C |
| Battery Type | Sealed Lead Acid |
| Communication | USB, Serial |
| Humidity | 0-95% non-condensing |
| Certifications | CE |
Explains symbols used on UPS for important information.
Details UPS power connection and electrical requirements for 5-6KVA models.
Procedures for connecting UPS to a common AC power source with qualified personnel.
Describes the UPS front panel's graphical LCD, buttons, and indicators.
Covers user-configurable settings like language, date/time, LCD, alarms, and access.
Step-by-step guide for powering on the UPS and verifying normal operation.
Instructions on how to start the UPS using battery power without utility input.
Steps required to safely shut down the UPS unit and its connected loads.
Information on UPS battery lifespan and notification for replacement.
Detailed procedure for replacing internal batteries in rack-mount UPS units.
Step-by-step guide for replacing internal batteries in Tower 0-3KVA UPS units.
Instructions for replacing internal batteries in Tower 5-6KVA UPS units.
Procedure for replacing Extended Battery Modules (EBMs) on all UPS models.
A chart to diagnose common UPS alarms, faults, and their possible causes and actions.
To Next Page
