What to do if Eaton 9SX3000 shows power overload?
If the Power overload LED is On and the UPS beeps continuously, it means that the power requirements exceed the UPS capacity. To resolve this, remove some of the equipment from the UPS. Note that the UPS continues to operate, but may switch to Bypass mode or shut down if the load increases.
Why is the Eaton 9SX3000 battery mode LED on?
The Battery mode LED is On with 1 beep every 10 seconds because a utility failure has occurred, and the UPS is now in Battery mode. The UPS is using battery power to keep your equipment running. You should prepare your equipment for shutdown.
What to do if my Eaton UPS doesn't start?
If the Eaton UPS doesn't start, there might be several reasons. First, check the input connections to ensure the input source is correctly connected. Second, ensure that the Remote Power Off (RPO) switch is not active, and the RPO connector is properly connected. If the UPS Status menu displays the 'Remote Power Off' notice, inactivate the RPO input.
What to do if Eaton 9SX3000 UPS is overheating?
If the UPS overtemperature LED is On and it beeps every 3 seconds, it indicates that the UPS internal temperature is too high or a fan has failed. If the UPS transferred to Bypass mode, it will return to normal operation when the temperature drops 5 °C below the warning level. If the condition persists, shut down the UPS. Clear vents and remove any heat sources. Allow the UPS to cool. Ensure the airflow around the UPS is not restricted. Restart the UPS.
What to do if Eaton 9SX3000 UPS battery fault LED is on?
If the Battery fault LED is On and the UPS beeps continuously, it indicates that the battery test failed due to bad or disconnected batteries, or the battery minimum voltage is reached in ABM® cycling mode. Verify that all batteries are properly connected. Start a new battery test.
Why Eaton 9SX3000 UPS battery low LED is on?
The Battery low LED is On and the UPS beeps every 3 seconds because the UPS is in Battery mode and the battery is running low. This warning is approximate, and the actual time to shutdown may vary significantly. Depending on the UPS load and number of Extended Battery Modules (EBMs), the 'Battery Low' warning may occur before the batteries reach 20% capacity.
How to fix Eaton 9SX3000 not providing expected backup time?
If the Eaton UPS isn't providing the expected backup time, it could be that the batteries need charging or service. To address this, apply utility power for 48 hours to charge the batteries.
What to do if Eaton 9SX3000 no battery LED is on?
If no battery LED is On and the UPS beeps continuously, it means that the batteries are disconnected. Verify that all batteries are properly connected.
General| Power Rating | 3000 VA |
|---|---|
| Output Power | 2700 W |
| Topology | Double Conversion Online |
| Form Factor | Tower |
| Input Frequency | 50/60 Hz |
| Output Frequency | 50/60 Hz |
| Transfer Time | 0 ms |
| Input Voltage | 200-240 V |
| Output Voltage | 220/230/240 V |
| Battery Type | Lead-acid |
| Efficiency | Up to 96% |
| Communication | USB, Serial |
| Typical Backup Time | Varies based on load |
| Output Receptacles | IEC 320 C13 (6), IEC 320 C19 (2) |
Examples of symbols used on the UPS to alert users to important information.
Safety precautions for personnel and guidelines for safe UPS installation and operation.
Essential precautions for handling and operating the UPS unit safely.
Details on connecting the UPS to power, required protective devices, and cable cross-sections.
Instructions for accessing the terminal block and performing common input source connections.
Details on programmable signal inputs and the Remote Power Off (RPO) function.
Instructions for testing remote control and details on programmable signal outputs.
Step-by-step guide for starting up the UPS and ensuring normal operation.
Information on battery lifespan and notifications for replacement.
Warnings, cautions, and general notes to consider before replacing UPS batteries.
Step-by-step instructions for replacing the internal battery pack in rack-mounted UPS units.
Step-by-step instructions for replacing the internal battery pack in tower 0-3KVA UPS units.
Instructions for replacing the internal battery pack in tower 5-6KVA UPS units.
Detailed steps for disconnecting and removing battery trays during replacement.
Instructions for inserting new battery packs and reassembling the UPS cover.
Procedures for replacing Extended Battery Modules (EBMs) on all UPS models.
Chart to help diagnose common UPS alarms and faults with possible causes and actions.
Troubleshooting steps for UPS overtemperature and failure to start.
To Next Page
