What does F13 Repeated Reset Fault mean on ECA PROTEUS PREMIX PPR Boiler?
If the ECA Boiler displays 'F13: Repeated Reset Fault', it indicates that the reset button has been pressed more than 5 times in an hour. In this situation, contact a gas safe engineer.
What to do if my ECA PROTEUS PREMIX PPR shows F37 Low Water Pressure Fault?
When the ECA Boiler shows 'F37: Low Water Pressure Fault', it means the water pressure is too low. Begin by checking the water pressure in your boiler's heating system. Add water to the system until the pressure is between 1.5 and 2 bar; the boiler should clear the error once the pressure exceeds 0.8 bar. Inspect your valves and system for any leaks. If the issue persists, contact a gas safe engineer.
What does E02 False Flame Indication mean on my ECA PROTEUS PREMIX PPR?
If your ECA Boiler displays the error 'E02: False Flame Indication' (flame detected when the gas valve is closed), first press the reset button. If the error continues after resetting, it is recommended to contact a gas safe engineer for assistance.
Why does my ECA Boiler show E03 High Limit Temperature Protection?
If the ECA Boiler shows 'E03: High Limit Temperature Protection', it means the CH return and CH supply temperatures have exceeded 90°C. Check that the water valves of the boiler installation are open. If the boiler triggers this error in winter mode, ensure that at least one radiator is open. Then, press the reset button. If the error persists, further assistance may be needed.
What causes F34 Low Supply Voltage error on ECA Boiler?
If the ECA Boiler displays 'F34: Low Supply Voltage', it indicates that the supply voltage has dropped below 170V. In this case, it is recommended to contact a gas safe engineer.
Why does my ECA PROTEUS PREMIX PPR Boiler show E80 Temperature Difference Error?
If the ECA Boiler displays 'E80: Temperature Difference Error between CH Return Water Temperature and CH Supply Water Temperature Sensor', it indicates that the temperature detected by the return sensor is higher than that of the supply sensor. Press the reset button. If the error continues, contact a gas safe engineer.
What does E33 Error on Temperature Sensor for CH Return Water mean on ECA PROTEUS PREMIX PPR?
If the ECA Boiler displays 'E33: Error on Temperature Sensor for CH Return Water', it indicates that the return water temperature sensor is in a short or open circuit state. If the error persists after resetting, contact authorized service or a gas safe engineer.
How to troubleshoot E35 Error on Temperature Sensor for CH Supply Water in ECA PROTEUS PREMIX PPR Boiler?
If the ECA Boiler displays 'E35: Error on Temperature Sensor for CH Supply Water', it means the CH supply temperature sensor is in a short or open circuit state. Press the reset button. If the error persists after resetting, contact a gas safe engineer.
What causes E08 Flame Circuit Failure in ECA PROTEUS PREMIX PPR?
If the ECA Boiler displays 'E08: Flame Circuit Failure', it could indicate that the electronic card has failed. Press the reset button. If the error persists after resetting, contact a gas safe engineer.
What does E16 error mean on my ECA PROTEUS PREMIX PPR Boiler?
If the ECA Boiler displays 'E16: Error on Temperature Sensor for CH Supply Water', it means that no temperature is being detected by the temperature sensor for CH supply. Press the reset button. If the error persists after the reset, contact a gas safe engineer.
Installer's responsibilities for boiler installation and start-up, including checks and user handover.
Essential safety instructions for gas leaks, handling, and general operation to prevent injury or damage.
Guidelines for water systems, gas supply lines, and their compliance with regulations.
Procedure and requirements for converting the boiler from Natural Gas to LPG.
Requirements for boiler installation, location, clearances, and environmental considerations.
Procedures and checks required for safely starting up the boiler after installation.
Instructions for safe operation, regular maintenance, and cleaning of the boiler.
Overview of applicable regulations and standards for boiler installation in the UK.
List of relevant British Standards codes of practice for boiler installation.
List of relevant Irish Standards applicable to boiler installations.
Guidelines for installing boilers in timber-framed buildings as per BS5440 and IGE.
Requirements for potable water system components to be approved by WRAS.
Prohibition of using artificially softened water for central heating systems.
Tips for optimizing boiler efficiency, safety, and reducing energy consumption.
Information on preventing and addressing clogging issues in old iron pipe installations.
Instructions for cleaning the boiler's outer casing and importance of periodic maintenance.
Details about the boiler's packaging, including dimensions and contents.
Identifies and describes the main components for HM, HST, and HCH boiler models.
Overview of the boiler's features, control panel, and integrated safety systems.
Provides detailed technical specifications including general data, flue lengths, and emission values.
Energy Performance Regulation (ERP) data for different boiler models.
Calculation methods for determining the energy efficiency of boiler packages.
Guidelines for selecting an appropriate and safe location for boiler installation.
Requirements for Type C boilers regarding air supply and installation room ventilation.
Step-by-step instructions for mounting the combi boiler on the wall.
Covers flue sizes, types, plume kits, placement distances, and available sets.
Instructions for connecting the condensate discharge and ensuring proper drainage.
General guidance for gas and water connections, including valve usage.
Guidelines for electrical connection, earthing, and fuse requirements.
Information on compatible room thermostats and their connection.
Details on connecting the outdoor sensor for weather-compensated heating.
Diagrams and instructions for connecting various controllers to the mainboard.
Step-by-step guide for filling the system with water and initial commissioning.
Procedure for switching the boiler off and information on anti-freeze function.
Explanation of the control panel buttons and their functions.
Description of the icons and displays on the boiler's LCD screen.
Details on operating modes like Standby, Air Purge, Winter, Summer, Comfort, ECO, and reminders like Annual Maintenance and Anti-Frost.
Table detailing gas settings, orifice sizes, and fan speeds for different models.
Instructions for registering the boiler warranty online or via QR code.
Comprehensive terms and conditions governing the boiler's warranty period and coverage.
Information on service appointment charges and spare parts guarantee.
Recommendations for maintaining high heating performance, including system cleaning and inhibitors.
Pump performance curves showing head vs. flow rate for different models.
To Next Page
General
