Echo PPT-260 - 01-05 User Manual

POWER PRUNER
TM
OPERATOR'S MANUAL
1
Power Pruner
TM
Operator's Manual
MODEL: PPT-260
WARNING DANGER
Read rules for safe operation and instructions carefully. ECHO provides an Operator's
Manual and a Safety Manual. Both must be read and understood for proper and safe
operation.
X753000772
10/05
X7532092202

Echo PPT-260 - 01-05 Specifications

General

Brand	Echo
Model	PPT-260 - 01-05
Category	Pole Saw
Language	English

Summary

Introduction to the Power Pruner

Operator's Manual Overview

Manual for operation, starting, stopping, maintenance, storage, and assembly.

Safety Manual Overview

Explains hazards and safety measures for Power Pruner use.

Safety Information and Symbols

Manual Safety Symbols and Keywords

Explains safety alerts, symbols, and keywords used in the manual.

International Symbols Explained

Lists and explains various international symbols used on the product and in the manual.

Personal Condition and Safety Equipment

Discusses physical fitness and necessary safety gear for operation.

Personal Safety Equipment Details

Eye Protection Standards

Recommends wearing eye protection meeting ANSI Z87.1 or CE requirements.

Face and Head Protection

Advises wearing head protection with a full face shield for overhead trimming.

Hand and Hearing Protection

Suggests gloves for grip/vibration reduction and hearing protection.

Proper Clothing and Footwear

Details appropriate attire, including snug clothing and safety shoes.

Environmental Safety Considerations

Discusses fatigue in hot weather and precautions for cold/vibration.

Advanced Safety Precautions

Repetitive Stress Injury Prevention

Discusses potential injuries from overuse and provides prevention steps.

Electrical Hazard Awareness

Warns about high voltages in overhead conductors and the unit's lack of insulation.

Ventilation and Exhaust Safety

Advises against indoor operation due to poisonous engine exhaust.

Work Area Safety and Firm Grip

Emphasizes clearing the area, warning bystanders, and holding the unit firmly.

Operation and Equipment Safety

Safe Stance and Operation Location

Details maintaining balance, avoiding slippery surfaces, and operating from the ground.

Branch Hazards and Retreat Path

Advises assessing branch hazards and planning a retreat path.

Saw Chain and Hot Surface Precautions

Warns to avoid contact with the saw chain and hot surfaces.

Equipment Inspection and Approved Accessories

Instructs unit inspection and warns against non-approved accessories.

Guide Bar and Saw Chain Checks

Details checks for cutting attachment security, condition, and work area debris.

Kickback and Emissions Control

Understanding and Preventing Kickback

Explains kickback, its causes, and how to prevent accidents.

Emission Control System Information

Identifies emission systems, provides engine info, and mentions label/durability.

Product Identification

Safety Decal Locations

Instructs to locate and understand safety decals on the unit.

Main Component Overview

Shows key components with their locations indicated by numbers.

Component Descriptions

Power Head and Controls

Describes the power head, throttle trigger, lockout, and stop switch.

Cutting and Drive System Parts

Details the cutting attachment, guide bar, saw chain, and oiler.

Shaft, Guards, and Handles

Describes the lower shaft tube, guards, and handle assembly.

Fuel, Ignition, and Starting Systems

Explains the fuel tank, primer bulb, choke, and starter.

Air Cleaner and Muffler

Describes the air cleaner assembly and muffler system.

Assembly Instructions

Required Tools and Parts for Assembly

Lists the necessary tools and parts for product assembly.

Drive Shaft and Power Head Connection

Step-by-step instructions for attaching the drive shaft to the power head.

Aligning and Securing Components

Guides on aligning couplers, rotating the shaft, and tightening bolts securely.

Cutting Attachment Installation

Preparing Attachment and Tubes for Connection

Loosening screws, clamp knob, and extending upper tube.

Connecting Drive Shafts and Tubes

Aligning and joining the inner drive shaft with the cutting attachment shaft.

Securing the Cutting Attachment

Aligning ridges, holes, and tightening screws and the clamp knob.

Throttle Linkage and Chain Tension

Throttle Linkage Adjustment and Connection

Steps for connecting the throttle linkage and checking its movement.

Ignition Lead Connection and Management

Connecting ignition leads and bundling them against the engine.

Saw Chain Tension Adjustment Process

Loosening nuts, adjusting tension, and tightening nuts.

Fueling the Power Pruner

Fuel and Oil Specifications

Specifies gasoline octane, oil standards, and approved oil.

Safe Fuel Handling and Mixing

Critical warnings for handling fuel and step-by-step mixing instructions.

Fuel Storage Best Practices

Advice on storing fuel safely and using fresh fuel.

Lubrication System Maintenance

Automatic Oiling System Operation

Explains the automatic oiler's function and how to fill the reservoir.

Adjusting Automatic Oiler Volume

Details how to adjust the oiler screw for desired oil volume.

Starting a Cold Engine

Cold Start Preparation and Safety

Pre-start checks, stop switch, choke, and primer bulb usage.

Recoil Starter Operation for Cold Start

How to engage and pull the recoil starter for engine ignition.

Post-Fire Adjustments and Warm-up

Moving choke to 'Run', continued recoil start, and engine warm-up.

Reaching Operating Throttle Speed

Gradually increasing engine RPM to operating speed after warm-up.

Starting a Warm Engine

Warm Start Procedure Overview

Outlines the starting procedure for a warm engine, omitting choke use.

Idle Operation Warning and Correction

Warns about attachment movement at idle and suggests carburetor adjustment.

Warm Engine Recoil Starting

Procedure for pulling the recoil starter for a warm engine.

Engine Stopping and Pruning Techniques

Engine Stopping Procedure

Instructions for stopping the engine using the throttle and stop switch.

Emergency Engine Stall Method

Describes using the choke to stall the engine if the stop switch fails.

Pruning Techniques and Safety

Covers limb size, planning, branch handling, and avoiding hazards.

Cutting Methods and Pressure Control

Details multi-stage cutting for larger limbs and controlling pressure.

Prohibited Pruning Uses

States the unit is not for felling or bucking.

Maintenance Procedures Overview

Maintenance Skill Level Guide

Defines skill levels (1, 2, 3) for performing maintenance tasks.

REPOWER™ Maintenance Kits

Mentions availability of maintenance kits and parts from dealers.

Recommended Dealer Maintenance Tasks

Lists maintenance tasks recommended to be performed by an Echo dealer.

Do-It-Yourself Maintenance Tasks

Lists maintenance tasks that can be performed by the user.

Air Filter and Fuel Filter Maintenance

Air Filter Cleaning and Inspection Steps

Steps for cleaning and inspecting the air filter element.

Air Filter Replacement Considerations

Mentions that carburetor adjustment might be needed after replacement.

Fuel Filter Replacement Procedure

Step-by-step guide to replace the fuel filter using a hook tool.

Spark Plug and Cooling System Service

Spark Plug Inspection, Cleaning, and Gap

How to remove, check, clean, adjust gap, or replace the spark plug.

Spark Plug Tightening Torque Specification

Specifies the torque for tightening the spark plug.

Cooling System Cleaning Importance

Explains the necessity of airflow through cylinder fins for cooling.

Preventing Engine Overheating and Cleaning

Lists reasons for overheating and cleaning cylinder fins as a solution.

Exhaust System Maintenance

Spark Arrestor Screen Cleaning Procedure

Steps to access and clean the spark arrestor screen.

Engine Cover Removal and Cylinder Cleaning

Instructions for removing engine covers and cleaning cylinder fins.

Muffler, Exhaust Port, and Carburetor Service

Catalytic Muffler Component Cleaning

Steps to clean carbon deposits from muffler components.

Cylinder Exhaust Port Cleaning Schedule

Recommends cleaning the exhaust port every 3 months for emissions compliance.

Carburetor Adjustment Basics and Break-in

Covers engine break-in period and high altitude adjustment.

Carburetor Adjustment and Chain Replacement

Idle Speed Adjustment Procedure

How to check and adjust idle speed using a tachometer and screw.

Guide Bar and Chain Replacement Safety

Safety warnings and initial steps for replacing the guide bar and chain.

Removing Guide Bar and Chain Components

Instructions for loosening nuts, removing cover, and detaching bar/chain.

Guide Bar and Chain Replacement Continued

Installing Guide Bar and Chain Components

Steps for installing the new guide bar and chain onto the gear case.

Adjusting Saw Chain Tension Correctly

Detailed steps on how to adjust saw chain tension correctly.

Filing Saw Chain

Saw Chain Filing Tools and Safety Precautions

Lists required tools and emphasizes safety precautions before filing.

Filing Cutter Edges and Depth Gauge Usage

Instructions for filing cutter edges and using depth gauges.

Raker Sharpening and Post-Filing Cleaning

Finishing by rounding raker edges and cleaning filings.

Troubleshooting Engine Problems

Engine Not Starting or Hard Starting Issues

Troubleshooting steps for engine start issues.

Engine Running Poorly or Dying

Troubleshooting steps for when the engine runs but not properly.

Engine Not Cranking Issues

Troubleshooting steps for when the engine does not crank.

Ignition Spark Testing Safety Warning

Safety warning about testing ignition spark near the cylinder plug hole.

Storage and Long-Term Maintenance

Long Term Storage Preparation Steps

Maintenance steps required for storing the unit for extended periods.

Fuel System Preparation for Storage

How to drain the fuel tank and remove fuel from the carburetor.

Cylinder Lubrication and Final Storage Steps

Pouring oil into cylinder, installing spark plug, and covering guide bar.

Product Specifications

Model and Physical Specifications Overview

Lists model, length, width, height, and weight.

Engine and Fuel System Specifications

Details engine type, displacement, fuel requirements, and oil ratio.

Component and Performance Specifications

Lists clutch, sprocket, gear ratio, speeds, and capacities.

Guide Bar and Chain Specifications Details

Specifics on the guide bar length and saw chain pitch.

Servicing Information and Support

Parts and Authorized Service Dealer Information

Information on obtaining parts and locating authorized service dealers.

Consumer Product Support and Warranty Registration

Contact details for support and warranty registration instructions.

Obtaining Additional Manuals and Videos

How to obtain replacement manuals and safety videos.