Need help?Do you have a question about the Echo PPT-260 - 01-05 and is the answer not in the manual?
Manual for operation, starting, stopping, maintenance, storage, and assembly.
Explains hazards and safety measures for Power Pruner use.
Explains safety alerts, symbols, and keywords used in the manual.
Lists and explains various international symbols used on the product and in the manual.
Discusses physical fitness and necessary safety gear for operation.
Recommends wearing eye protection meeting ANSI Z87.1 or CE requirements.
Advises wearing head protection with a full face shield for overhead trimming.
Suggests gloves for grip/vibration reduction and hearing protection.
Details appropriate attire, including snug clothing and safety shoes.
Discusses fatigue in hot weather and precautions for cold/vibration.
Discusses potential injuries from overuse and provides prevention steps.
Warns about high voltages in overhead conductors and the unit's lack of insulation.
Advises against indoor operation due to poisonous engine exhaust.
Emphasizes clearing the area, warning bystanders, and holding the unit firmly.
Details maintaining balance, avoiding slippery surfaces, and operating from the ground.
Advises assessing branch hazards and planning a retreat path.
Warns to avoid contact with the saw chain and hot surfaces.
Instructs unit inspection and warns against non-approved accessories.
Details checks for cutting attachment security, condition, and work area debris.
Explains kickback, its causes, and how to prevent accidents.
Identifies emission systems, provides engine info, and mentions label/durability.
Instructs to locate and understand safety decals on the unit.
Shows key components with their locations indicated by numbers.
Describes the power head, throttle trigger, lockout, and stop switch.
Details the cutting attachment, guide bar, saw chain, and oiler.
Describes the lower shaft tube, guards, and handle assembly.
Explains the fuel tank, primer bulb, choke, and starter.
Describes the air cleaner assembly and muffler system.
Lists the necessary tools and parts for product assembly.
Step-by-step instructions for attaching the drive shaft to the power head.
Guides on aligning couplers, rotating the shaft, and tightening bolts securely.
Loosening screws, clamp knob, and extending upper tube.
Aligning and joining the inner drive shaft with the cutting attachment shaft.
Aligning ridges, holes, and tightening screws and the clamp knob.
Steps for connecting the throttle linkage and checking its movement.
Connecting ignition leads and bundling them against the engine.
Loosening nuts, adjusting tension, and tightening nuts.
Specifies gasoline octane, oil standards, and approved oil.
Critical warnings for handling fuel and step-by-step mixing instructions.
Advice on storing fuel safely and using fresh fuel.
Explains the automatic oiler's function and how to fill the reservoir.
Details how to adjust the oiler screw for desired oil volume.
Pre-start checks, stop switch, choke, and primer bulb usage.
How to engage and pull the recoil starter for engine ignition.
Moving choke to 'Run', continued recoil start, and engine warm-up.
Gradually increasing engine RPM to operating speed after warm-up.
Outlines the starting procedure for a warm engine, omitting choke use.
Warns about attachment movement at idle and suggests carburetor adjustment.
Procedure for pulling the recoil starter for a warm engine.
Instructions for stopping the engine using the throttle and stop switch.
Describes using the choke to stall the engine if the stop switch fails.
Covers limb size, planning, branch handling, and avoiding hazards.
Details multi-stage cutting for larger limbs and controlling pressure.
States the unit is not for felling or bucking.
Defines skill levels (1, 2, 3) for performing maintenance tasks.
Mentions availability of maintenance kits and parts from dealers.
Lists maintenance tasks recommended to be performed by an Echo dealer.
Lists maintenance tasks that can be performed by the user.
Steps for cleaning and inspecting the air filter element.
Mentions that carburetor adjustment might be needed after replacement.
Step-by-step guide to replace the fuel filter using a hook tool.
How to remove, check, clean, adjust gap, or replace the spark plug.
Specifies the torque for tightening the spark plug.
Explains the necessity of airflow through cylinder fins for cooling.
Lists reasons for overheating and cleaning cylinder fins as a solution.
Steps to access and clean the spark arrestor screen.
Instructions for removing engine covers and cleaning cylinder fins.
Steps to clean carbon deposits from muffler components.
Recommends cleaning the exhaust port every 3 months for emissions compliance.
Covers engine break-in period and high altitude adjustment.
How to check and adjust idle speed using a tachometer and screw.
Safety warnings and initial steps for replacing the guide bar and chain.
Instructions for loosening nuts, removing cover, and detaching bar/chain.
Steps for installing the new guide bar and chain onto the gear case.
Detailed steps on how to adjust saw chain tension correctly.
Lists required tools and emphasizes safety precautions before filing.
Instructions for filing cutter edges and using depth gauges.
Finishing by rounding raker edges and cleaning filings.
Troubleshooting steps for engine start issues.
Troubleshooting steps for when the engine runs but not properly.
Troubleshooting steps for when the engine does not crank.
Safety warning about testing ignition spark near the cylinder plug hole.
Maintenance steps required for storing the unit for extended periods.
How to drain the fuel tank and remove fuel from the carburetor.
Pouring oil into cylinder, installing spark plug, and covering guide bar.
Lists model, length, width, height, and weight.
Details engine type, displacement, fuel requirements, and oil ratio.
Lists clutch, sprocket, gear ratio, speeds, and capacities.
Specifics on the guide bar length and saw chain pitch.
Information on obtaining parts and locating authorized service dealers.
Contact details for support and warranty registration instructions.
How to obtain replacement manuals and safety videos.
To Next Page
General