The EcoRider X62 is a self-balancing personal transporter designed for both entertainment and leisure, as well as a transportation vehicle for various commuting tools. It operates on the principle of "dynamic stability," automatically balancing itself. The scooter's posture, rider, and scooter are determined by a built-in precision gyroscope, which, through a central microprocessor, calculates the appropriate command to drive the motor to achieve the balancing effect. The X62 is a new type of personal transporter, distinct from traditional unicycles or bi-axial wheel scooters, and is suitable for both formal occasions and off-road use. It is commonly known as an electric scooter.
Function Description:
The X62 uses the principle of dynamic balance, where the body's movements continuously adjust to achieve the correct balance. It is designed to be low-cost to run, non-pollutant, quiet, and convenient. The X62 can run for approximately 4-5 hours when fully charged.
Important Technical Specifications:
The X62 has two wheels, with a width suitable for an ordinary adult. It weighs approximately 40kg. It is powered by 2 lithium-ion batteries.
Here are some key technical parameters:
- Material: Magnesium Alloy + Aluminum Alloy + ABS + Rubber
- Recommended Age: 12 - 60 years
- Recommended Height: 130 - 200cm
- Max Speed: 20KM/H
- Max Mileage: 75 - 80Km (for the 15.6Ah battery version)
- Max Load: 150Kg
- Min Turning Radius: 0°
- Max Climbing: ≤ 35°
- Height of Pedal: 220mm
- Max Height of Ground: 125mm
- Tire Size: 19 inch
- Standard Pressure: 150 kpa 21psi
- LongWidthHigh: 488 * 836 * 1080-1480mm (Adjustable)
- Net Weight: 39.6kg
- Gross Weight: 48.3kg
- Working Temperature: -10 - +40 °C
- Storage Temperature: -20 - +50 °C
- Waterproof: IP54
- Beginner Mode: Yes, set via APP
- Applicable Terrain: Cement Road / Asphalt road / Grass / Gravel Road / Beach
Motherboard Parameters (Double System):
- Battery: SAMSUNG18650 Lithium Ion Battery
- Rated Voltage: 57.6V
- Max Charging Voltage: 67.2V
- Rated Capacity: 7.8Ah or 15.6Ah
- Intelligent BMS: Over voltage Protection / Under voltage Protection / Short circuit Protection / Overheating protection, Automatic sleep / Wake
- Motor: Brushless DC Motor
- Rated Power: 1200W x 2 = 2400W
- Charger Parameters:
- Input Voltage: 100 - 240V
- Output Voltage: 67.2V
- Output Current: 2.0A or 3.0A
- Rated Power: 120W
- Charging Time: 3 - 4 Hour (for 7.8Ah) or 4 - 5 Hour (for 15.6Ah)
- Charging Temperature: 0 - 40 °C
- Operating Mode: Standby mode / Pulling mode / Speed limit driving mode / Normal driving mode / Remote mode / Lock mode
- Display Panel: 6.5" OLED Display / Battery / Speed / Mileage / Lamp / Lock / Bluetooth
- Light: Front lamp / Ambient light / Left / Right turn light / Brake light / Backup light
- Wireless Connections: Bluetooth
- APP: Yes
- Voice: Yes
- USB Charging: Yes (5V/1A)
- Bluetooth Music: Yes
- Colour: White / Silver / Space gray / Champagne gold
- GPS: Option
Usage Features:
- Preparation Before Use: Before assembly, the battery should be charged for at least 5 hours. Ensure all parts are tightened, undamaged, and wear all the protection equipment recommended (Helmet, elbow guards, and knee pads).
- App Guide:
- Downloading the App: Download the "iRobot" app from the App Store (iOS) or by scanning the QR code (Android).
- App Control Panel: The app provides an overview of the scooter's status (speed, battery, temperature, GPS, faults), settings (modify scooter name, LED lights, scooter voice, auto balance, language, horizontal position, steering sensitivity, maximum speed), and support (beginner lessons, video lessons, FAQ, after-sales service, feedback, technical parameters, about iRobot).
- Connecting to Smartphone: Turn on the X62, open 'Bluetooth' on your mobile phone, open the iRobot app, and press the icon to pair your phone to the X62.
- WARNING: If there is more than 1 machine, turn on and pair only one machine at a time, otherwise all machines will be paired to the same phone.
- Assembling the X62:
- Check the Accessories: After unpacking, ensure all parts are present: X62 main body (x1), LeanSteer (x1), Handgrip (x1), Charger (x1), Tool (x1), Screws (x4), User manual (x1), Warranty card (x1).
- Preparation before assembly: Locate the Phillips screwdriver. Wear gloves to avoid injury.
- Mount handlebar and leansteer frame: Insert the handlebar into the leansteer frame, fasten the height adjuster nut, and fasten the clockwise joint.
- Install the battery pack: Lay the X62 mainframe on its back, exposing the underside of the battery housing. Install the battery pack using the M6 x 20 hexagon socket cap head screws and a 5mm hexagonal allen key.
- Function Introduction:
- OLED Display: The display shows icons for light, fault, lock, Bluetooth, warning, speed, battery, and battery percentage.
- Power Button, USB Port and Charge Port: Located at the back of the mainframe, the X62 has a USB charging port (5V/1A current) and a charge port.
- Power switch functions: To turn on, press the power switch for 2 seconds. The LED display on the footplate will light up. To turn off, press the power switch for 2 seconds.
- Charging Method:
- Find the charging port at the back of the X62 mainframe, open the cover to the charging port, and check that the charging port is dry.
- Connect the charging port with the charger (100~240V, global common), then plug it into the power AC supply.
- When the LED indicator on the charger turns red, it means the scooter is charging normally; when the indicator turns green, the scooter is fully charged. Unplug the charging cable to save the battery life.
- WARNING: For safety reasons, and to prolong the life of the battery, do not leave the battery plugged in when the unit is fully charged and showing a green light.
- How to use the parking stand: To release, strike the button on the front of the body with your shoe. The parking stand will automatically release. To retract, use the front of your shoe to push the parking stand to the upmost parking position.
- Guide for safe riding and handling:
- Awareness: The X62 is a transportation vehicle. Be cautious, maintain a safe distance from others, and comply with traffic laws. Wear a helmet, wrist pads, elbow and knee pads. Check battery status before each ride. Do not ride when under the influence of alcohol or sedatives. Follow safety guides.
- General Safety Instructions:
- Get instructions from an experienced person.
- Understand all workings of the smartphone app and its settings.
- Do not use in any place prohibited by law.
- Keep your body at least 5cm distance from the operation bar.
- Remember that you will be at least 20cm taller than usual when standing on the X62.
- Do not use in areas unsuitable for riding (pits, fissures, slopes, puddles).
- Do not ride the X62 upstairs or downstairs.
- Do not lift the X62 off the ground unevenly.
- Do not take the X62 on the motorway.
- Do not ride with more than one passenger, especially a small child or baby in a harness.
- Do not take both hands off the steering bar at the same time.
- Do not allow persons of less than 14 years, or more than 65 years to ride unaccompanied.
- Do not allow pets on the X62.
- Do not allow pregnant ladies to ride.
- Do not allow those impaired by drugs, alcohol, mentally or physically disabled, or those with known heart disease to ride the X62.
- Do not ride the machine in a dangerous environment (fire, flammables, steam, gas, liquid, dust).
- Avoid riding backward at high speed, or making sharp turns when riding backwards.
- Do not use mobile phones when handling the X62.
- Do not ride in poor weather and road conditions (heavy rain, snow, ice).
- Do not disregard any warnings in this manual.
- Do not allow others to ride unless they have read and understood safety instructions or watched the safety video.
- Place any carried goods in the front or side storage or in a backpack. Do not place carried goods on the footplate as it will influence the balance.
- Make sure the X62 is switched off completely before carrying it, as injury may be caused by the quick rotation of the wheels. It is suggested that the vehicle be carried by 2 people by holding the frame NOT by holding the mudguard, as this may break and cause personal injury.
- Automatic / Intelligent Safety:
- Speed Limiter: The X62 automatically limits the maximum speed. In beginner mode (8km/hr) and skillful mode (20km/hr), if the speed is exceeded, the leansteer bar generates a pushback force to push the rider slightly backwards to stop the vehicle from accelerating. The rider must adjust their body to the leansteer bar, keeping at least a fist's distance. The rider continues to lean forward and presses on the leansteer bar, which may cause loss of balance and falls. The vehicle must always be in balance with the rider.
- Steep Slope / Overload: If the rider remains on a steep slope for a long time, the footplate will recline to remind the rider to get off rather than overload and strain the motor. Similar situations that would trigger this response include deep pits and heavy weight. If the rider is reminded to get off the vehicle, it can be pushed ahead by using ASSISTANCE MODE.
- Critical Battery Power: If the X62 is showing critical battery power (usually less than 10%), the footplate will recline to prompt the rider to get off the unit. If the rider ignores this and continues to ride, the unit may stop suddenly. Going backward at a fast speed, going up steep slopes, or riding a steep incline will drain the battery quickly. An audible warning will be heard.
- Learning to ride the X62:
- Going forward and backward:
- Having fully charged the vehicle, unplug the X62 from the mains.
- Turn on the power switch, and you will hear an audible welcome. The light on the Signal Indicator will come on, meaning the vehicle has started normally.
- BEFORE YOU STEP ONTO THE MACHINE, make sure that the pedals are on the horizontal level.
- Standing directly behind the X62, hold the handlebar grip with one or two hands, and keeping the leansteer bar upright, adjust the handlebar grip until the pedals become horizontal – then step onto the machine with one foot.
- Place your centre of gravity on the pedal gradually, and raise the other foot (similar to walking upstairs).
- Avoid moving the leansteer bar.
- Lean your body forward very slowly, and feel the X62 move forward.
- Recover your posture slowly to the upright position, and feel the vehicle decelerate and stop.
- Practice items (g) and (h) until you are comfortable with moving and stopping.
- Checking first that there is nothing behind you, lean your body backward slightly, and you will start to go backward.
- Slowly bring your body to the upright position, and you will slow and then stop.
- WARNING: Beginners should not dismiss these early steps, and learn to master them to prevent any injury or accident.
- WARNING: It is not recommended to drive backwards for more than a few steps. Whenever possible, turn the vehicle using a left or right turn.
- Stopping the vehicle:
- Slowly move your body against the direction in which you are travelling.
- Bring your buttocks downward (as though you are going to sit down).
- After the X62 stops, distribute your weight evenly on the footplate to achieve balance.
- NOTE: IF YOU CONTINUE TO TILT BACKWARDS, THE VEHICLE WILL MOVE BACKWARDS.
- Turning Left and Right: If you turn the steering bar in the left or right direction, the X62 will turn in the corresponding direction. Keep your knees slightly bent and tilted toward the direction in which you want to turn – the angle should be that of the leansteer bar (similar to skiing).
- Getting off the X62: Getting off the X62 is similar to walking down the stairs. For the first few attempts, ask your instructor to hold the leansteer bar.
- Keeping the X62 balanced by holding the leansteer bar with both hands, take your feet off the footplate one foot at a time.
- Stabilize your body, and do not move the leansteer bar when dismounting.
- Do not take your hands off the steering bar before the X62 is switched off, even though your feet are no longer on the machine, as the machine will move forward – possibly causing injury or damage.
- Assistance Mode: Once you are no longer on the X62, and using your smartphone app, you can turn the vehicle from the standby mode to assistance mode. In this programme, you can manoeuvre the vehicle manually using the leansteer bar.
- NOTE: YOU MUST ALWAYS HOLD THE STEERING BAR WHEN IN ASSISTANCE MODE, as the vehicle will move forward if unattended.
- NOTE: NEVER ATTEMPT TO RIDE THE X62 WHILE IN ASSISTANCE MODE, as the rider will have no control of the vehicle, and will cause injury to himself and the vehicle.
- Locking the X62: When not using your X62, open the smartphone app, and lock the vehicle using the padlock icon. After locking the X62, you will hear a voice prompt 'Locked'. Locking the vehicle itself cannot stop theft by it being carried away. Store your X62 in a safe place.
Maintenance Features:
- Cleaning the X62: To keep your X62 in good condition, clean it after each use. The X62 can be washed with a shower hose or garden hose with water pressure less than 1MPa (or 145PSI) to flush the mudguards. Pressure washing or soaking in water is not advised as this will cause serious damage to the X62. Dry the vehicle after hosing, and place in good ventilation so that the metal parts do not rust. For difficult stains on the plastic, a small amount of toothpaste applied to a soft cloth can be used. Store the X62 in a cool, dry place. Exposure to sun, and extreme heat and cold will accelerate the aging process of the X62.
- WARNING: When cleaning with water, ensure that the vehicle is powered off, and that the charging cable is unplugged, and the cover to the charging port is closed.
- Battery Maintenance and Transportation: The X62 battery should still perform well after 30,000 ~ 40,000Km if well maintained. Failure to maintain the battery will reduce the capacity or even damage the battery after only a few months.
- To extend the battery life, please observe the following:
- Read the notes on the battery pack surface and follow the instructions.
- Keep the battery pack in a dry environment at a temperature from 0C to 40C. Extreme high or low temperatures can affect battery life.
- Avoid storing or using the battery in an environment below -20C or above 50C.
- Prolonged exposure to a moist or wet environment may cause internal condensation. Remove the battery and store in a cool, dry place.
- Under normal conditions, avoid completely exhausting the battery and then recharging. Frequent charging does not affect the battery life, whereas long-term exhausted status will reduce the capacity and life of the battery.
- If the X62 is left unused, the battery will continue to consume power from the battery, therefore:
- for storage of less than 30 days, keep the battery fully charged.
- for storage of more than 30 days, remove the battery and store in a cool, dry place.
- for storage of more than 6 months, ensure that the battery is fully charged every 3-4 weeks.
Need help?
To Next Page
General