EGO ST1510E - Page 9

56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1510E 9
EN
◾ Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
◾ Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
◾ Keep handles and grasping surface dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
◾ Keep cables away from the working area of the
tool. During operation cables may be hidden from view
and can be accidentally damaged by the tool.
BATTERY TOOL USE AND CARE
◾ Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used with
another battery pack.
◾ Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
◾ When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a re.
◾ Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
◾ Do not use a battery pack or tool that is damaged
or modied. Damaged or modied batteries may
exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
◾ Do not expose a battery pack or tool to re
or excessive temperature. Exposure to re or
temperature above 100 °C may cause explosion.
◾ Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging
improperly or at temperatures outside the specied
range may damage the battery and increase the risk
of re.
SERVICE
◾ Have your power tool serviced by a qualied repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
◾ Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
WARNING: Read all safety warnings,
instructions, illustrations and specications
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock,
re and/or serious injury. Save all warnings and
instructions for future reference.
Save all warnings and instructions for future
reference.
TRAINING
◾ Read the instructions carefully. Be familiar with the
controls and the proper use of the machine.
◾ Never allow people unfamiliar or children with these
instructions to use the appliance. Local regulations can
restrict the age of the operator.
◾ Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
PREPARATION
◾ Never operate the machine while people, especially
children, or pets are nearby.
◾ Wear eye protection and stout shoes at all times while
operating the machine.
◾ The distance between the machine and bystanders shall
be at least 15m.
◾ Never operate the machine while the operator is tried, ill
or under the inuence of alcohol or other drugs.
OPERATION
◾ Use the machine only in daylight or good articial light.
◾ Never operate the machine with damaged guards or
shields or without guards or shields in place.
◾ Switch on the motor only when the hands and feet are
away from the cutting means.
◾ Always disconnect the machine from the power supply
(i.e. remove the battery pack).
◾ whenever leaving the machine unattended;
◾ before clearing a blockage;
◾ before checking, cleaning or working on the
machine.