To Next PageTo Next PageWhy EINHELL GC-PM 40/1 S engine does not start?
If your EINHELL Lawn Mower engine doesn't start, try these steps: * Ensure the engine start/stop lever is pressed. * Check the throttle lever position (if your model has one). * Replace the spark plug if it's defective. * Refuel if the fuel tank is empty. * Actuate the fuel pump (primer) if your model has one.
What to do if EINHELL GC-PM 40/1 S leaves lawn yellow, uneven cut?
If your EINHELL Lawn Mower isn't cutting evenly and the lawn turns yellow, it could be due to a few reasons. The blade might not be sharp enough, so try sharpening it. Also, the cutting height might be too low; adjust it to a more appropriate level. Lastly, ensure the engine speed isn't too low by setting the throttle lever to max (if your lawnmower has one).
Why EINHELL GC-PM 40/1 S Lawn Mower engine does not run smoothly?
If the engine of your EINHELL Lawn Mower isn't running smoothly, the air filter might be dirty, so try cleaning it. Another potential cause is a dirty spark plug, which should also be cleaned.
What to do if EINHELL GC-PM 40/1 S Lawn Mower grass chute is not clean?
If the grass chute of your EINHELL Lawn Mower isn't clean, it could be because the engine speed is too low. Try setting the throttle lever to maximum. It might also be that the cutting height is too small, so set it properly. A worn blade can also cause this issue, so replace the blade if necessary. Finally, check if the grass bag is clogged and empty it if it is.
How to fix EINHELL GC-PM 40/1 S Lawn Mower that vibrates intensively?
If your EINHELL Lawn Mower doesn't operate smoothly and vibrates intensively, check if any bolts are loose and tighten them. Also, make sure the blade attachment is secure. If the blade is imbalanced, consider replacing it.
General| Engine Type | 4-stroke |
|---|---|
| Cutting Width | 40 cm |
| Grass Catcher Volume | 45 L |
| Working speed | 2800 rpm |
| Cutting Height Adjustment | 3-level |
Explains warning signs on the equipment as shown in Figure 14, covering various safety aspects.
Details the various parts and components of the lawn mower as depicted in figures 1 through 12.
Lists all the components included in the product package and instructions for checking completeness.
Provides detailed sound pressure, sound power levels, and vibration emission values for the equipment.
Provides step-by-step instructions and notes for assembling the lawn mower components before initial use.
Explains how to adjust the cutting height of the lawn mower, emphasizing engine off.
Instructions for performing a safety test on the engine start/stop lever to ensure proper function before operation.
Step-by-step guide on how to start the petrol lawn mower engine, including primer use.
Provides advice and best practices for mowing, including blade condition, lines, and inclines.
Provides instructions for thoroughly cleaning the lawn mower, including specific advice on methods and agents.
Refers to a separate manual for maintenance intervals and notes on disposing of materials.
Instructions for checking the oil level in the petrol engine, including specific steps and warnings.
Provides guidelines for blade sharpening, balancing, mounting, and changing, emphasizing professional service.
Instructions for lubricating the axles and wheel hubs, including removal of wheel caps.
Guidance on oiling actuator cables and checking their smooth movement for proper function.
Instructions for maintaining the air filter, including cleaning methods and frequency.
Details the process for cleaning the spark plug, including removal and reassembly steps.
Instructions for inspecting the V-belt by removing the V-belt cover.
Emphasizes ensuring safety parts are installed after repairs and liability for improper repairs.
Advises observing local regulations concerning lawn mower operating times.
Lists parts subject to normal wear and tear, required as consumables.
Lists parts considered consumables, such as blades.
Refers to checking for missing parts and contacting service if necessary.
