EINHELL GE-CM 18/30 Li - Solo - Proper Use; Intended Use and Restrictions; Technical Data; Residual Risks Identification

GB
- 27 -
4.
T
echnical data
See warranty card of your country
.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly
.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary
.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated.
The fol-
lowing hazards may arise in connection with
the equipment‘s construction and layout:
1.
Lung damage if no suitable protective dust
mask is used.
2.
Damage to hearing if no suitable ear protec-
tion is applied.
Warning!
This equipment generates an electromag-
netic
Þ
eld during operation.
Under certain
circumstances this
Þ
eld may actively or pas-
sively impede medical implants.
T
o reduce
the risk of serious or fatal injuries, we recom-
mend persons with medical implants to con-
sult their doctor and the manufacturer of the
medical implant prior to using the equipment.
5.
Before starting the equipment
Article is supplied without a battery pack and
without a charger.
The lawn mower is delivered partly assembled.
The push bar and the grass basket must be as-
sembled before using the lawn mower.
Follow the
instructions step by step and refer to the pictures
when assembling.
Warning! Always pull out the safety plug be-
fore making adjustments to the equipment.
Fitting the push bar (Fig.
3a to 3c)
T
ake a bottom push bar (Fig.
2 /Item 3) and fasten
it with the nut (Fig.
2/Item 13) as shown in Fig.
3a.
Proceed in the same way on the other side.
Screw
the top push bar (Fig.
2/Item 2) to the bottom
push bar (Fig.
2/Item 3) as shown in Fig.
3b.
Then attach the power cable to the push bar (Fig.
2/Item 14) using the cable clips (Fig.
3c).
Mounting the grass basket (Fig.
4a to 4c)
Plug the bottom and the top part of the grass box
together (Fig.
4a/Item 9, 10).
Ensure that all the
plastic lugs engage correctly
.
Next push the grass
box handle (Fig.
4b/Item 11) into the openings on
the grass box.
Check that the handle is secure
and correctly positioned.
Before you
Þ
t the grass
basket you must ensure that the motor is swit-
ched o
Ů
and the blade is not rotating.
The grass box must be attached to the two hooks
on the mower.
T
o do this, open the ejector
ß
ap
with one hand (Fig.
4c/Item 7) and attach the
grass box with the other hand.
The ejector
ß
ap is
held against the grass box by a spring.
Adjusting the cutting height
Warning!
Adjust the cutting height only when the motor has
been switched o
Ů
and the safety plug has been
disconnected.
Before you begin to mow
, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged.
T
o prevent any imbalance, replace
blunt and/or damaged blades.
T
o carry out this
check,
Þ
rst switch o
Ů
the motor and pull out the
safety plug.
The cutting height is adjusted as shown in Figure
5.
T
o do so, turn the equipment upside down or tilt
it to the side.
Position both the front and rear axle
in the same notch, so that the cutting blade runs
parallel to the lawn.
Position
Cutting depth
1
70mm
2
50mm
3
30mm
Charging the battery (Fig.
6)
1.
T
ake the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2.
Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger.
Insert the power plug of the charger
(17) into the socket outlet.
The green LED will
then begin to
ß
ash.
3.
Insert the battery pack (16) into the battery
Anl_SA_GE_CM_18_30_Li_Solo_ARG.indb 27
24.07.2018 09:28:50